CARRIAGEBOLT5/16−18X.625, Auger 30 LH | Husqvarna 1130SB specification

REPAIR PARTS

AUGER HOUSING / IMPELLER ASSEMBLY

SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
	1	532 40 77-21 AUGER HOUSING
	2	532 40 76-45 SCRAPPER BAR
3 (5x)	3	872 27 05-05	CARRIAGEBOLT5/16−18X.625
3 (5x)	4	532 15 53-77	NUT 5/16−18

4 (5x)

01.07.003-A

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	532 40 77-23	AUGER 30 LH
2	532 40 77-22	AUGER 30 RH

01.07.013-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 22

Image 22

Husqvarna 1130SB owner manual CARRIAGEBOLT5/16−18X.625, Auger 30 LH, Auger 30 RH

Contents

1130SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEY Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engine HOW to USE Your Snow Thrower Stopping To Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See Fig Before Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations Lubrication Cleaning Engine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Storage Other Troubleshooting Repair Parts KEY Part Description Auger 30 LH CARRIAGEBOLT5/16−18X.625Auger 30 RH Plastic Retainer Repair Parts Auger Housing / Impeller AssemblySkid Plate Weight BAR CARRIAGEBOLT5/16−18X.750 Deflector Weldment Deflector Control AssemblyChute Weldment Knob Black LEVER/CABLE Rotator Assembly Gray 532 42 11-61 Rotator Pivot Bracket 532 42 Lower Tube Handles Rear Plate Clutch ROD13 532 41 54-33 Shifter Plate Bracket 532 17 86-66 Halogen Headlight 532 42 14-48 Headlight Bezel GrayBulb 532 18 00-82 Intermediate Gear Rubber Wheel Ring 532 40 61-09 Control Shaft AssemblyAssembly Flange Bearing 14 15 532 19 77-63 Drive Plate Weldment 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly 11 532 18 40-76 Shifter Support Bracket Gear Axle ShaftRoll PIN 3/16 Clik PIN Frame Repair Partschassis / Engine / PulleysEngine TEC Model Bottom PAN Steer Cable Bracket LH Steer Cable Bracket RH Axle Lobe Wheel LobeLever PIN Retainer PIN Power Cord532 03 50-62 Safety Ignition KEY Wrench 532 18 10-35 DECAL, DANGER, Deflector Decals10 532 18 37-30 DECAL, Remote Deflector Warranty Statement

REPAIR PARTS

KEY

CARRIAGEBOLT5/16−18X.625

KEY

AUGER 30 LH

AUGER 30 RH