Manuals / Husqvarna / Lawn and Garden / Snow Blower

Husqvarna 1130SB Repair Parts, Drive, Description, 40 49-23assy of 1a,1b AXLE ASSEMBLY

Models: 1130SB

1 40

Download 40 pages 8.09 Kb

Page 34

Image 34

REPAIR PARTS

DRIVE

SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43

	7
1b	4
8	3
	3
1b
7	1a
	1a

	2
5	3
5
	4
6	01.03.001-A

KEY	PART		DESCRIPTION
NO.	NO.		DESCRIPTION
1	532	40 49-23 (assy of 1a,1b) AXLE ASSEMBLY
1a	532	40 43-07	AXLE SHAFT
1b	532	18 42-06	ROLL PIN 3/16
2	532	18 00-81	GEAR

3532 17 46-97 THRUST WASHER

4532 17 98-30 AXLE BEARING

5532 14 63-15 SCREW 5/16−18 X .625

6817 49 05-08 BOLT 5/16−18 X .500

7	532 15 54-43	CLIK PIN
8	532 18 92-82	SQUARE KEY

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 34

Image 34

Husqvarna 1130SB owner manual Repair Parts, Drive, Description, 40 49-23assy of 1a,1b AXLE ASSEMBLY

Contents

1130SB Preparation TrainingOperation Maintenance and Storage TABLE OF CONTENTSPRODUCT SPECIFICATIONS CUSTOMER RESPONSIBILITIESPARTS PACKED SEPARATELY IN CARTON ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER REMOVE SNOW THROWER FROM CARTONINSTALL SPEED CONTROL ROD See Figs. 1 and ASSEMBLY / PRE-OPERATIONUNFOLD UPPER HANDLE ASSEMBLY / PRE-OPERATION INSTALL AUGER CONTROL ROD See Figs. 5 andASSEMBLY / PRE-OPERATION CHECK TIRE PRESSUREOPERATION KNOW YOUR SNOW THROWERMEETS A.N.S.I. SAFETY REQUIREMENTS OPERATIONTO USE CHOKE CONTROL See Fig HOW TO USE YOUR SNOW THROWEROPERATION STOPPINGOPERATION USING THE CLEAN-OUTTOOL See Fig.POWER STEERING OPERATION See Fig TO THROW SNOW See FigOPERATION BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig SCRAPER BAR See FigTO START ENGINE SNOW THROWING TIPSOPERATION BEFORE STOPPINGBEFORE EACH USE MAINTENANCEGENERAL RECOMMENDATIONS LUBRICATIONMAINTENANCE CLEANINGENGINE BELTSTO ADJUST SNOW THROWER HEIGHT SERVICE AND ADJUSTMENTS2.Remove safety ignition key SNOW THROWERSERVICE AND ADJUSTMENTS TO REPLACE BELTS See FigENGINE STORAGEOTHER SNOW THROWERDoes not start TROUBLESHOOTINGLoss of power Engine idles or1 9 2 REPAIR PARTSAUGER HOUSING / IMPELLER ASSEMBLY 35 22 21PART REPAIR PARTSAUGER HOUSING / IMPELLER ASSEMBLY DESCRIPTIONPART REPAIR PARTSAUGER HOUSING / IMPELLER ASSEMBLY DESCRIPTIONPART AUGER HOUSING / IMPELLER ASSEMBLYREPAIR PARTS DESCRIPTIONPART REPAIR PARTSAUGER HOUSING / IMPELLER ASSEMBLY DESCRIPTIONPART CONTROL PANEL / DISCHARGE CHUTEREPAIR PARTS DESCRIPTIONPART REPAIR PARTSCONTROL PANEL / DISCHARGE CHUTE DESCRIPTIONPART HANDLESREPAIR PARTS DESCRIPTIONPART REPAIR PARTSHANDLES DESCRIPTIONHANDLES REPAIR PARTS1532 18 04-80IMPELLER ROD ASSEMBLY PARTPART REPAIR PARTSHANDLES DESCRIPTIONPART DRIVEREPAIR PARTS DESCRIPTIONDRIVE REPAIR PARTS1415 DRIVE REPAIR PARTS1532 19 84-74SPEED SELECTOR HEAD ASSEMBLY PARTDRIVE REPAIR PARTS40 49-23assy of 1a,1b AXLE ASSEMBLY PARTDESCRIPTION REPAIR PARTSCHASSIS / ENGINE / PULLEYSPART PARTPART WHEELSREPAIR PARTS DESCRIPTIONWHEELS REPAIR PARTS532 40 51-61COVER 532 03 50-62SAFETY IGNITION KEY BAG OF PARTSREPAIR PARTS PARTPART DECALSREPAIR PARTS DESCRIPTIONSECTION 3 ITEMS NOT COVERED BY THIS WARRANTY WARRANTY STATEMENTSECTION 1 LIMITED WARRANTY SECTION 4 EXCEPTIONS AND LIMITATIONS

40 49-23 (assy of 1a,1b) AXLE ASSEMBLY