532 42 14-48 Headlight Bezel Gray, Bulb

REPAIR PARTS

HANDLES

SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43

		KEY	PART
	3	NO.	NO.	DESCRIPTION
	2	1	532 41 62-88 INTERLOCK SPRING
5	2	2	532 41 45-72 INTERLOCK CAM
		3	532 17 88-31 TORSION SPRING
		4	532 16 96-75	RETAINER
	1	5	817 06 04-10 SCREW 1/4−20 X .625
	1	6	532 42 18-14 INTERLOCK STOP
		6	532 42 18-14 INTERLOCK STOP
6	01.08.007-B

			4
3			5	KEY	PART
7				KEY	PART	DESCRIPTION
7	2			NO.	NO.	DESCRIPTION
	2
				1	532 42 13-82 PANEL CONSOLE GRAY
				2	532 42 14-48 HEADLIGHT BEZEL GRAY
				3	532 17 86-66 HALOGEN HEADLIGHT
	4	1		4	532 18 44-71 SHOULDER SCREW
5	4			5	532 17 52-62 SCREW 10−24 X 1.25
5				5	532 17 52-62 SCREW 10−24 X 1.25
6				6	532 18 09-64 WIRE HARNESS
6				7	532 40 16-20	BULB
				7	532 40 16-20	BULB
	01.10.013-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 30

Image 30

Husqvarna 1130SB owner manual 532 42 14-48 Headlight Bezel Gray, 532 17 86-66 Halogen Headlight, Bulb

Contents

1130SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEY Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engine HOW to USE Your Snow Thrower Stopping To Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See Fig Before Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations Lubrication Cleaning Engine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Storage Other Troubleshooting Repair Parts KEY Part Description CARRIAGEBOLT5/16−18X.625 Auger 30 LHAuger 30 RH Repair Parts Auger Housing / Impeller Assembly Plastic RetainerSkid Plate Weight BAR CARRIAGEBOLT5/16−18X.750 Deflector Weldment Deflector Control AssemblyChute Weldment Knob Black LEVER/CABLE Rotator Assembly Gray 532 42 11-61 Rotator Pivot Bracket 532 42 Lower Tube Handles Clutch ROD Rear Plate13 532 41 54-33 Shifter Plate Bracket 532 42 14-48 Headlight Bezel Gray 532 17 86-66 Halogen HeadlightBulb 532 18 00-82 Intermediate Gear Rubber Wheel Ring 532 40 61-09 Control Shaft AssemblyAssembly Flange Bearing 14 15 532 19 77-63 Drive Plate Weldment 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly 11 532 18 40-76 Shifter Support Bracket Gear Axle ShaftRoll PIN 3/16 Clik PIN Frame Repair Partschassis / Engine / PulleysEngine TEC Model Bottom PAN Steer Cable Bracket LH Steer Cable Bracket RH Wheel Lobe Axle LobeLever PIN Retainer PIN Power Cord532 03 50-62 Safety Ignition KEY Wrench Decals 532 18 10-35 DECAL, DANGER, Deflector10 532 18 37-30 DECAL, Remote Deflector Warranty Statement

Husqvarna 1130SB 532 42 14-48 Headlight Bezel Gray, 532 17 86-66 Halogen Headlight, Bulb

Models: 1130SB

REPAIR PARTS

HANDLES

KEY

KEY

532 42 14-48 HEADLIGHT BEZEL GRAY

532 17 86-66 HALOGEN HEADLIGHT

BULB