Wheel Lobe, Axle Lobe, Lever PIN | Husqvarna 1130SB specification

REPAIR PARTS

WHEELS

SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43

2

								17					3	2
						20		17		23		4	3	1
						20		19			6	5
						16					6	5
				17	18	16			22		7
						15	18		22	9	7
						15	18			9	8
				16		24				10
				20		23		21		11
				19		22
				19						12
				21						12
									13	14
								14 13	13
						11		14 13
					10			12
2				8	9
2				7
	3	4	5	6
2	1 01.15.001-A
				KEY	PART			DESCRIPTION
				NO.	NO.			DESCRIPTION
				1	532 40 51-61 COVER

2532 18 44-71 SHOULDER SCREW

3812 00 00-45 RETAINER RING

4532 19 21-26 WHEEL DRIVER

5532 18 24-66 RETAINER RING

6	532 18 76-22	WHEEL LOBE
7	532 19 49-41 CLUTCH SLIDE
8	532 17 91-39	SPRING
9	532 18 92-82	SQUARE KEY
10	532 19 49-40	AXLE LOBE

11532 17 46-97 THRUST WASHER

12532 19 95-19 STEERING YOKE

13532 18 41-97 STEERING BRACKET

14817 49 05-08 SCREW 5/16−18 X .50

15532 19 95-11 PIVOT BRACKET

16	532 19 95-18 BELLCRANK

17532 18 18-47 BELLCRANK PIN

18817 60 04-06 SCREW 1/4−20 X .375

19532 40 50-77 STEERING LINK

20	532 70 02-79	RETAINER
21	532 08 51-79	RETAINER
22	532 19 38-85	SPRING
23	532 18 20-15	LEVER PIN
24	532 19 95-12 PIVOT BRACKET

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 37

Image 37

Husqvarna 1130SB owner manual Wheel Lobe, Axle Lobe, Lever PIN

Contents

1130SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEY Recoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower Power Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See Fig Before Starting the Engine To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE Lubrication Engine Cleaning To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig Other Storage Troubleshooting Repair Parts KEY Part Description Auger 30 LH CARRIAGEBOLT5/16−18X.625Auger 30 RH Plastic Retainer Repair Parts Auger Housing / Impeller AssemblySkid Plate CARRIAGEBOLT5/16−18X.750 Weight BAR Chute Weldment Deflector Control AssemblyDeflector Weldment Knob Black 532 42 11-61 Rotator Pivot Bracket LEVER/CABLE Rotator Assembly Gray Lower Tube 532 42 Handles Rear Plate Clutch ROD13 532 41 54-33 Shifter Plate Bracket 532 17 86-66 Halogen Headlight 532 42 14-48 Headlight Bezel GrayBulb Assembly Rubber Wheel Ring 532 40 61-09 Control Shaft Assembly532 18 00-82 Intermediate Gear Flange Bearing 14 15 Trunnion Bearing Assembly 532 19 84-74 Speed Selector Head Assembly532 19 77-63 Drive Plate Weldment 11 532 18 40-76 Shifter Support Bracket Roll PIN 3/16 Axle ShaftGear Clik PIN Engine TEC Model Repair Partschassis / Engine / PulleysFrame Bottom PAN Steer Cable Bracket RH Steer Cable Bracket LH Axle Lobe Wheel LobeLever PIN 532 03 50-62 Safety Ignition KEY Power CordRetainer PIN Wrench 532 18 10-35 DECAL, DANGER, Deflector Decals10 532 18 37-30 DECAL, Remote Deflector Warranty Statement