Power Cord, Retainer PIN, Wrench | Husqvarna 1130SB specs

REPAIR PARTS

BAG OF PARTS

SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43

		4
		14			6	7
	13	5			6	7
	13					KEY	PART
	12
	12							DESCRIPTION
			8		9	NO.	NO.	DESCRIPTION
					9
						1	532 19 85-63	POWER CORD
						1	532 19 85-63	POWER CORD
						2	532 16 96-75	RETAINER PIN
						3	532 18 06-84	WRENCH
3				10	11	4	532 18 45-05 REMOTE SPRING
				10		5	532 17 98-29 SHOULDER BOLT 1/4−20
						5	532 17 98-29 SHOULDER BOLT 1/4−20
						6	532 17 92-46 NYLON WASHER 1/4−20
						7	532 19 17-30 LOCKNUT 1/4−20
						8	872 25 05-05 CARRIAGE BOLT 5/16−18 X 5/8
						9	532 75 11-53 LOCKNUT 5/16−18
						10	873 80 06-00 LOCKNUT 3/8−16
						11	819 13 13-16	WASHER 3/8
						12	532 19 86-36 SHEAR BOLT 1/4−20 X 1−3/4
						13	532 19 86-38	SPACER
						14	873 80 04-00 LOCKNUT 1/4−20
	2			1
				1
				01.14.003-A

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
01.14.008-A	1	532 03 50-62 SAFETY IGNITION KEY

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 38

Page 38

Image 38

Husqvarna 1130SB owner manual Power Cord, Retainer PIN, Wrench, 532 03 50-62 Safety Ignition KEY

Contents

1130SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEY Meets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engine HOW to USE Your Snow Thrower Stopping To Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See Fig Before Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations Lubrication Cleaning Engine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Storage Other Troubleshooting Repair Parts KEY Part Description Auger 30 RH CARRIAGEBOLT5/16−18X.625Auger 30 LH Skid Plate Repair Parts Auger Housing / Impeller AssemblyPlastic Retainer Weight BAR CARRIAGEBOLT5/16−18X.750 Deflector Weldment Deflector Control AssemblyChute Weldment Knob Black LEVER/CABLE Rotator Assembly Gray 532 42 11-61 Rotator Pivot Bracket 532 42 Lower Tube Handles 13 532 41 54-33 Shifter Plate Bracket Clutch RODRear Plate Bulb 532 42 14-48 Headlight Bezel Gray532 17 86-66 Halogen Headlight 532 18 00-82 Intermediate Gear Rubber Wheel Ring 532 40 61-09 Control Shaft AssemblyAssembly Flange Bearing 14 15 532 19 77-63 Drive Plate Weldment 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly 11 532 18 40-76 Shifter Support Bracket Gear Axle ShaftRoll PIN 3/16 Clik PIN Frame Repair Partschassis / Engine / PulleysEngine TEC Model Bottom PAN Steer Cable Bracket LH Steer Cable Bracket RH Lever PIN Wheel LobeAxle Lobe Retainer PIN Power Cord532 03 50-62 Safety Ignition KEY Wrench 10 532 18 37-30 DECAL, Remote Deflector Decals532 18 10-35 DECAL, DANGER, Deflector Warranty Statement

REPAIR PARTS

BAG OF PARTS

KEY

POWER CORD

RETAINER PIN

WRENCH

WASHER 3/8

KEY

532 03 50-62 SAFETY IGNITION KEY