Chute Weldment, Deflector Weldment, Knob Black | Husqvarna 1130SB

REPAIR PARTS

CONTROL PANEL / DISCHARGE CHUTE

SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43

5

7

3

14

15

				*13
	KEY	PART		2
	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION	4
	1	532 40 76-50	CHUTE WELDMENT	4
	1	532 40 76-50	CHUTE WELDMENT
	2	532 18 41-13	DEFLECTOR WELDMENT

6

*9

*8

*10

3	532 42 06-73	DEFLECTOR CONTROL ASSEMBLY	6
4	532 42 03-25 DEFLECTOR SEAL
5	532 41 42-80	KNOB BLACK	1
6	532 12 84-15	POP RIVET	1
7	817 50 10-10 SCREW 10−24 X .625
*8	532 17 98-29 SHOULDER SCREW
*9	532 17 92-46 PLASTIC WASHER
*10	532 19 17-30	NUT 1/4−20
*11	872 25 05-05 CARRIAGE BOLT 5/16−18 X .50
*12	532 75 11-53	NUT 5/16−18
*13	532 18 45-05 DEFLECTOR SPRING

14532 42 06-79 (SERVICE PART) DEFLECTOR CONTROL HEAD

15532 42 06-72 (SERVICE PART) DEFLECTOR CONTROL CABLE

*12

*11

01.09.002-B

NOTE:

1.ALL ITEMS INDICATED WITH AN * ARE PROVIDED IN THE BAG OF ITEMS SHIPPED LOOSE WITH PRODUCT.

2.ITEMS 14 AND 15 ARE SERVICE PART NUMBERS TO ALLOW PURCHASE OF INDIVIDUAL ITEMS IF NECES- SARY.

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

25

Image 25

Husqvarna 1130SB owner manual Chute Weldment, Deflector Weldment, Deflector Control Assembly, Knob Black, POP Rivet

Contents

1130SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEY Recoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower Power Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See Fig Before Starting the Engine To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE Lubrication Engine Cleaning To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig Other Storage Troubleshooting Repair Parts KEY Part Description Auger 30 LH CARRIAGEBOLT5/16−18X.625Auger 30 RH Plastic Retainer Repair Parts Auger Housing / Impeller AssemblySkid Plate CARRIAGEBOLT5/16−18X.750 Weight BAR Chute Weldment Deflector Control AssemblyDeflector Weldment Knob Black 532 42 11-61 Rotator Pivot Bracket LEVER/CABLE Rotator Assembly Gray Lower Tube 532 42 Handles Rear Plate Clutch ROD13 532 41 54-33 Shifter Plate Bracket 532 17 86-66 Halogen Headlight 532 42 14-48 Headlight Bezel GrayBulb Assembly Rubber Wheel Ring 532 40 61-09 Control Shaft Assembly532 18 00-82 Intermediate Gear Flange Bearing 14 15 Trunnion Bearing Assembly 532 19 84-74 Speed Selector Head Assembly532 19 77-63 Drive Plate Weldment 11 532 18 40-76 Shifter Support Bracket Roll PIN 3/16 Axle ShaftGear Clik PIN Engine TEC Model Repair Partschassis / Engine / PulleysFrame Bottom PAN Steer Cable Bracket RH Steer Cable Bracket LH Axle Lobe Wheel LobeLever PIN 532 03 50-62 Safety Ignition KEY Power CordRetainer PIN Wrench 532 18 10-35 DECAL, DANGER, Deflector Decals10 532 18 37-30 DECAL, Remote Deflector Warranty Statement