Repair Parts Auger Housing / Impeller Assembly

REPAIR PARTS	AUGER HOUSING / IMPELLER ASSEMBLY
SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43
	1
	3
	2

	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
	1	532 18 79-25 AUGER BALL BEARING
3	2	532 18 81-70	PLASTIC RETAINER
3	3	532 17 95-82	SCREW 5/16−18 X 1.00
	3	532 17 95-82	SCREW 5/16−18 X 1.00
	01.07.006-A

	3
		1
3
	KEY	PART	DESCRIPTION
	NO.	NO.	DESCRIPTION
	1	532 40 78-34	SKID PLATE
	2	872 27 05-06	CARRIAGE BOLT 5/16−18 X .750
01.11.002-A	3	532 75 11-53	NUT 5/16−18

2	1

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 23

Image 23

Husqvarna 1130SB owner manual Repair Parts Auger Housing / Impeller Assembly, Plastic Retainer, Skid Plate

Contents

1130SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in Carton Unfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Ignition KEY OperationKnow Your Snow Thrower Primer Recoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See Fig Before Starting the Engine If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before Stopping Lubrication MaintenanceGeneral Recommendations Before Each USE Engine Cleaning Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute Deflector To Replace Belts See Fig Other Storage Troubleshooting Repair Parts KEY Part Description Auger 30 RH CARRIAGEBOLT5/16−18X.625Auger 30 LH Skid Plate Repair Parts Auger Housing / Impeller AssemblyPlastic Retainer CARRIAGEBOLT5/16−18X.750 Weight BAR Knob Black Deflector Control AssemblyChute Weldment Deflector Weldment 532 42 11-61 Rotator Pivot Bracket LEVER/CABLE Rotator Assembly Gray Lower Tube 532 42 Handles 13 532 41 54-33 Shifter Plate Bracket Clutch RODRear Plate Bulb 532 42 14-48 Headlight Bezel Gray532 17 86-66 Halogen Headlight Flange Bearing Rubber Wheel Ring 532 40 61-09 Control Shaft AssemblyAssembly 532 18 00-82 Intermediate Gear 14 15 11 532 18 40-76 Shifter Support Bracket 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly 532 19 77-63 Drive Plate Weldment Clik PIN Axle ShaftRoll PIN 3/16 Gear Bottom PAN Repair Partschassis / Engine / PulleysEngine TEC Model Frame Steer Cable Bracket RH Steer Cable Bracket LH Lever PIN Wheel LobeAxle Lobe Wrench Power Cord532 03 50-62 Safety Ignition KEY Retainer PIN 10 532 18 37-30 DECAL, Remote Deflector Decals532 18 10-35 DECAL, DANGER, Deflector Warranty Statement

Husqvarna 1130SB Repair Parts Auger Housing / Impeller Assembly, Plastic Retainer, Skid Plate

Models: 1130SB

REPAIR PARTS

AUGER HOUSING / IMPELLER ASSEMBLY

KEY

PLASTIC RETAINER

KEY

SKID PLATE