532 42, Lower Tube | Husqvarna 1130SB specification

REPAIR PARTS

HANDLES

SNOW THROWER - MODEL NO. 1130SB (96193004300), PRODUCT NO. 961 93 00-43

			KEY	PART	DESCRIPTION
			NO.	NO.	DESCRIPTION
4	4		1	532 42 11-20 LOOP HANDLE LH
4			2	532 42 11-21 LOOP HANDLE RH
4			3	874 78 05-24 SCREW 5/16−18 X 1.50
		1	3	874 78 05-24 SCREW 5/16−18 X 1.50
		1	4	532 75 11-53	NUT 5/16−18
3			4	532 75 11-53	NUT 5/16−18
3
4
3
2

01.08.004-B

01.05.001-B

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	532 42 10-59	LOWER TUBE

2532 41 54-89 PIVOT SUPPORT

3817 00 05-12 BOLT 5/16−18 X .750

4817 00 06-16 SCREW 3/8−16 X 1.00

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 27

Page 27

Image 27

Husqvarna 1130SB owner manual 532 42, Lower Tube

Contents

1130SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Ignition KEY OperationKnow Your Snow Thrower Primer Recoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow Thrower To Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See Fig Before Starting the Engine If Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before Stopping Lubrication MaintenanceGeneral Recommendations Before Each USE Engine Cleaning Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute Deflector To Replace Belts See Fig Other Storage Troubleshooting Repair Parts KEY Part Description CARRIAGEBOLT5/16−18X.625 Auger 30 LHAuger 30 RH Repair Parts Auger Housing / Impeller Assembly Plastic RetainerSkid Plate CARRIAGEBOLT5/16−18X.750 Weight BAR Knob Black Deflector Control AssemblyChute Weldment Deflector Weldment 532 42 11-61 Rotator Pivot Bracket LEVER/CABLE Rotator Assembly Gray Lower Tube 532 42 Handles Clutch ROD Rear Plate13 532 41 54-33 Shifter Plate Bracket 532 42 14-48 Headlight Bezel Gray 532 17 86-66 Halogen HeadlightBulb Flange Bearing Rubber Wheel Ring 532 40 61-09 Control Shaft AssemblyAssembly 532 18 00-82 Intermediate Gear 14 15 11 532 18 40-76 Shifter Support Bracket 532 19 84-74 Speed Selector Head AssemblyTrunnion Bearing Assembly 532 19 77-63 Drive Plate Weldment Clik PIN Axle ShaftRoll PIN 3/16 Gear Bottom PAN Repair Partschassis / Engine / PulleysEngine TEC Model Frame Steer Cable Bracket RH Steer Cable Bracket LH Wheel Lobe Axle LobeLever PIN Wrench Power Cord532 03 50-62 Safety Ignition KEY Retainer PIN Decals 532 18 10-35 DECAL, DANGER, Deflector10 532 18 37-30 DECAL, Remote Deflector Warranty Statement

REPAIR PARTS

HANDLES

KEY

KEY

532 42 10-59

LOWER TUBE