Rider 11 R Rider 11 C
Rider 13 C
Rider 16 C AWD
Rider 16 C
CONTENTS
Contents
CONTENTS
Service journal
INTRODUCTION
Dear Customer
Driving and transport on public roads
Towing
Serial Number
Good service
INTRODUCTION
Pre-delivery service
Service journal
After the first 8 hours
KEY TO SYMBOLS
Symbols
KEY TO SYMBOLS
Starting instructions Check the engine’s oil level
Check the hydrostat’s oil level Lift up the cutting unit
Apply and lock the parking brake If the engine is cold, use the choke
SAFETY INSTRUCTIONS
Safety instructions
Insure your Rider
General use
Driving on slopes
This is what you do
WARNING! You must use approved personal
IMPORTANT INFORMATION
Maintenance
WARNING! The battery contains lead and
Children
WARNING! The engine and the exhaust
SAFETY INSTRUCTIONS
Transport
IMPORTANT INFORMATION
WHAT IS WHAT?
Location of the controls
PRESENTATION
Presentation
Clutch pedal Rider 11R and Rider 11 C
Brake pedal / Parking brake
Cutting height adjustment lever
Exercise care and refuel outdoors see safety instructions
Cutting unit
Lifting lever for the cutting unit
Release lever Rider 13 C, Rider 16 C
Release lever Rider 16 AWD
Clutch control, rear axle
Clutch control, front axle
Driving
Before starting
Start the engine
IMPORTANT INFORMATION
Starting the engine with a weak battery
Connecting the jump leads
Remove the cables in the reverse order
WARNING! Never run the engine indoors, in
Driving the Rider
2 For Rider 13 C, Rider 16 AWD and Rider 16 C
3 For Rider 11 R and Rider 11 C
Driving
Cutting tips
Stop the engine
Starting on a slope, manual gearbox. Rider 11 R and Rider 11 C
WARNING! Clear the lawn from stones and
Maintenance
Maintenance schedule
Daily maintenance
WARNING! No service procedures must be
Cleaning
Removing of the machine hoods
Engine cover
Front cover
Checking and adjusting the steering wires
Adjusting the brake Rider 11R and Rider 11 C
Checking the brake Rider 11 R and Rider 11 C
Maintenance
Adjusting the parking brake Rider 13 C, Rider 16 C
Adjusting the parking brake Rider AWD
Adjusting the throttle wire
WARNING! A poorly adjusted brake can
Maintenance
Replacing the air filter
IMPORTANT INFORMATION
Replacement of fuel filter
Controlling the acid level in a dry- charged battery
WARNING! Procedures on contact with acid
Checking the fuel pump’s air filter
Ignition system
Fuses
Replacing the spark plug
Maintenance
Check the safety system
Maintenance
Rider 16 AWD
Maintenance
28 - English
Checking and adjustment of the cutting unit’s ground pressure
when the engine is running. Mind your fingers
Checking the engine’s cooling air intake
Checking the cutting unit’s parallelism
Adjusting the parallelism of the cutting unit
Service position for the cutting unit
Placing in the service position
Rider 11 C, 13 C, 16 C, 16 AWD
Restoring from service position
Maintenance
Checking the blades
Removing the BioClip plug
Rider 11 C, 13 C, 16 C, 16 AWD
Rider 11 R
Lubrication
Checking the engine’s oil level
Replacing the engine oil
WARNING! Engine oil can be very hot if it is
Lubricating the belt adjuster
Lubrication Rider 11 R and Rider C
General lubrication
Rider 16 AWD
Problem
Troubleshooting schedule
Procedure
Service
Storage
Winter storage
Guard
TECHNICAL DATA
Dimensions
Engine
Electrical system
Rider 13 C
TECHNICAL DATA
Dimensions
Engine
Rider 16 C
TECHNICAL DATA
Dimensions
Engine
EC-declaration of conformity Applies to Europe only
TECHNICAL DATA
Page
´z+S!¶6¶¨ ´z+S!¶6¶¨
Page
1151019-26
´z+S!¶6¶¨ ´z+S!¶6¶¨