Rider 16 C
Rider 11 R Rider 11 C
Rider 13 C
Rider 16 C AWD
Service journal
CONTENTS
Contents
CONTENTS
Towing
INTRODUCTION
Dear Customer
Driving and transport on public roads
Serial Number
Good service
INTRODUCTION
Pre-delivery service
Service journal
After the first 8 hours
Symbols
KEY TO SYMBOLS
Apply and lock the parking brake If the engine is cold, use the choke
KEY TO SYMBOLS
Starting instructions Check the engine’s oil level
Check the hydrostat’s oil level Lift up the cutting unit
General use
SAFETY INSTRUCTIONS
Safety instructions
Insure your Rider
IMPORTANT INFORMATION
Driving on slopes
This is what you do
WARNING! You must use approved personal
WARNING! The engine and the exhaust
Maintenance
WARNING! The battery contains lead and
Children
SAFETY INSTRUCTIONS
Transport
IMPORTANT INFORMATION
Location of the controls
WHAT IS WHAT?
Brake pedal / Parking brake
PRESENTATION
Presentation
Clutch pedal Rider 11R and Rider 11 C
Lifting lever for the cutting unit
Cutting height adjustment lever
Exercise care and refuel outdoors see safety instructions
Cutting unit
Clutch control, front axle
Release lever Rider 13 C, Rider 16 C
Release lever Rider 16 AWD
Clutch control, rear axle
IMPORTANT INFORMATION
Driving
Before starting
Start the engine
WARNING! Never run the engine indoors, in
Starting the engine with a weak battery
Connecting the jump leads
Remove the cables in the reverse order
Driving
Driving the Rider
2 For Rider 13 C, Rider 16 AWD and Rider 16 C
3 For Rider 11 R and Rider 11 C
WARNING! Clear the lawn from stones and
Cutting tips
Stop the engine
Starting on a slope, manual gearbox. Rider 11 R and Rider 11 C
WARNING! No service procedures must be
Maintenance
Maintenance schedule
Daily maintenance
Front cover
Cleaning
Removing of the machine hoods
Engine cover
Maintenance
Checking and adjusting the steering wires
Adjusting the brake Rider 11R and Rider 11 C
Checking the brake Rider 11 R and Rider 11 C
WARNING! A poorly adjusted brake can
Adjusting the parking brake Rider 13 C, Rider 16 C
Adjusting the parking brake Rider AWD
Adjusting the throttle wire
Maintenance
Replacing the air filter
IMPORTANT INFORMATION
Checking the fuel pump’s air filter
Replacement of fuel filter
Controlling the acid level in a dry- charged battery
WARNING! Procedures on contact with acid
Maintenance
Ignition system
Fuses
Replacing the spark plug
Maintenance
Check the safety system
Rider 16 AWD
Maintenance
28 - English
Checking the cutting unit’s parallelism
Checking and adjustment of the cutting unit’s ground pressure
when the engine is running. Mind your fingers
Checking the engine’s cooling air intake
Rider 11 C, 13 C, 16 C, 16 AWD
Adjusting the parallelism of the cutting unit
Service position for the cutting unit
Placing in the service position
Maintenance
Restoring from service position
Rider 11 R
Checking the blades
Removing the BioClip plug
Rider 11 C, 13 C, 16 C, 16 AWD
WARNING! Engine oil can be very hot if it is
Lubrication
Checking the engine’s oil level
Replacing the engine oil
Rider 16 AWD
Lubricating the belt adjuster
Lubrication Rider 11 R and Rider C
General lubrication
Problem
Troubleshooting schedule
Procedure
Guard
Service
Storage
Winter storage
Electrical system
TECHNICAL DATA
Dimensions
Engine
Engine
Rider 13 C
TECHNICAL DATA
Dimensions
Engine
Rider 16 C
TECHNICAL DATA
Dimensions
TECHNICAL DATA
EC-declaration of conformity Applies to Europe only
Page
´z+S!¶6¶¨ ´z+S!¶6¶¨
Page
´z+S!¶6¶¨ ´z+S!¶6¶¨
1151019-26