Rider 13 C
Rider 11 R Rider 11 C
Rider 16 C AWD
Rider 16 C
Contents
CONTENTS
CONTENTS
Service journal
Dear Customer
INTRODUCTION
Driving and transport on public roads
Towing
Serial Number
Good service
INTRODUCTION
Pre-delivery service
Service journal
After the first 8 hours
Symbols
KEY TO SYMBOLS
Starting instructions Check the engine’s oil level
KEY TO SYMBOLS
Check the hydrostat’s oil level Lift up the cutting unit
Apply and lock the parking brake If the engine is cold, use the choke
Safety instructions
SAFETY INSTRUCTIONS
Insure your Rider
General use
This is what you do
Driving on slopes
WARNING! You must use approved personal
IMPORTANT INFORMATION
WARNING! The battery contains lead and
Maintenance
Children
WARNING! The engine and the exhaust
SAFETY INSTRUCTIONS
Transport
IMPORTANT INFORMATION
Location of the controls
WHAT IS WHAT?
Presentation
PRESENTATION
Clutch pedal Rider 11R and Rider 11 C
Brake pedal / Parking brake
Exercise care and refuel outdoors see safety instructions
Cutting height adjustment lever
Cutting unit
Lifting lever for the cutting unit
Release lever Rider 16 AWD
Release lever Rider 13 C, Rider 16 C
Clutch control, rear axle
Clutch control, front axle
Before starting
Driving
Start the engine
IMPORTANT INFORMATION
Connecting the jump leads
Starting the engine with a weak battery
Remove the cables in the reverse order
WARNING! Never run the engine indoors, in
2 For Rider 13 C, Rider 16 AWD and Rider 16 C
Driving the Rider
3 For Rider 11 R and Rider 11 C
Driving
Stop the engine
Cutting tips
Starting on a slope, manual gearbox. Rider 11 R and Rider 11 C
WARNING! Clear the lawn from stones and
Maintenance schedule
Maintenance
Daily maintenance
WARNING! No service procedures must be
Removing of the machine hoods
Cleaning
Engine cover
Front cover
Adjusting the brake Rider 11R and Rider 11 C
Checking and adjusting the steering wires
Checking the brake Rider 11 R and Rider 11 C
Maintenance
Adjusting the parking brake Rider AWD
Adjusting the parking brake Rider 13 C, Rider 16 C
Adjusting the throttle wire
WARNING! A poorly adjusted brake can
Maintenance
Replacing the air filter
IMPORTANT INFORMATION
Controlling the acid level in a dry- charged battery
Replacement of fuel filter
WARNING! Procedures on contact with acid
Checking the fuel pump’s air filter
Fuses
Ignition system
Replacing the spark plug
Maintenance
Maintenance
Check the safety system
Rider 16 AWD
Maintenance
28 - English
when the engine is running. Mind your fingers
Checking and adjustment of the cutting unit’s ground pressure
Checking the engine’s cooling air intake
Checking the cutting unit’s parallelism
Service position for the cutting unit
Adjusting the parallelism of the cutting unit
Placing in the service position
Rider 11 C, 13 C, 16 C, 16 AWD
Maintenance
Restoring from service position
Removing the BioClip plug
Checking the blades
Rider 11 C, 13 C, 16 C, 16 AWD
Rider 11 R
Checking the engine’s oil level
Lubrication
Replacing the engine oil
WARNING! Engine oil can be very hot if it is
Lubrication Rider 11 R and Rider C
Lubricating the belt adjuster
General lubrication
Rider 16 AWD
Problem
Troubleshooting schedule
Procedure
Storage
Service
Winter storage
Guard
Dimensions
TECHNICAL DATA
Engine
Electrical system
TECHNICAL DATA
Rider 13 C
Dimensions
Engine
TECHNICAL DATA
Rider 16 C
Dimensions
Engine
TECHNICAL DATA
EC-declaration of conformity Applies to Europe only
Page
´z+S!¶6¶¨ ´z+S!¶6¶¨
Page
´z+S!¶6¶¨ ´z+S!¶6¶¨
1151019-26