Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 13C, 16CAWD, 11R, 11C manual Service journal, Pre-delivery service, After the ﬁrst 8 hours

Models: 11C 11R 16C 16CAWD 13C

1 44

Download 44 pages 525 b

Page 5

Service journal

Service journal

Pre-delivery service

11a. Dry-charged battery (506788801) Top up battery with acid and charge for four hours.

1b. Wet-charged battery (510138501) Charge the battery for 4 hours at max. 3 amp.

2Fit steering wheel, seat and any optional equipment.

3Check and adjust tyre pressure (60 Kpa, 0.6 bar, 9 PSI).

4 Adjust cutting unit:

Adjust lift springs (effective weight of cutting unit should be 12-15kg / 26.5-33 lb).

Adjust cutting unit so that rear edge is about 2-4 mm / 1/8” higher than front edge.

Adjust cutting unit height setting so that cutting height limit is 5 mm / 3/16” above the frame of the unit at the lowest cutting height.

5Check that the right amount of oil is in the engine.

6Check that the right amount of oil is in the transmission. (Not Rider 11).

7 Connect battery.

8 Fill with fuel and start engine.

9Check that machine does not move in neutral.

10 Check: Forward drive.

Reverse drive.

Operation of blades.

Seat safety switch.

Lif lever safety switch.

Safety switch for the hydrostat pedals/neutral position.

Check engine speed. See the Technical data section.

11Check the synchronisation between the front and rear wheels. (Rider 16 AWD) See the workshop manual.

12Tell customer about:

Needs and beneﬁts of following the service schedule.

Servicing and the inﬂuence of this journal on the second-hand value of the machine.

Range of applications for BioClip.

Complete proof of sale etc.

Pre-delivery service carried out. No outstanding problems. Certiﬁed:

Date, mileage, stamp, signature

After the ﬁrst 8 hours

1 Change engine oil

2Change the oil in the gearbox. (Only AWD-machines)

English – 5

Image 5

Husqvarna 13C, 16CAWD, 11R, 11C manual Service journal, Pre-delivery service, After the ﬁrst 8 hours

Contents

Rider 13 C Rider 11 R Rider 11 CRider 16 C AWD Rider 16 CContents CONTENTSCONTENTS Service journalDear Customer INTRODUCTIONDriving and transport on public roads TowingINTRODUCTION Good serviceSerial Number After the ﬁrst 8 hours Service journalPre-delivery service Symbols KEY TO SYMBOLSStarting instructions Check the engine’s oil level KEY TO SYMBOLSCheck the hydrostat’s oil level Lift up the cutting unit Apply and lock the parking brake If the engine is cold, use the chokeSafety instructions SAFETY INSTRUCTIONSInsure your Rider General useThis is what you do Driving on slopesWARNING! You must use approved personal IMPORTANT INFORMATIONWARNING! The battery contains lead and MaintenanceChildren WARNING! The engine and the exhaustIMPORTANT INFORMATION TransportSAFETY INSTRUCTIONS Location of the controls WHAT IS WHAT?Presentation PRESENTATIONClutch pedal Rider 11R and Rider 11 C Brake pedal / Parking brakeExercise care and refuel outdoors see safety instructions Cutting height adjustment leverCutting unit Lifting lever for the cutting unitRelease lever Rider 16 AWD Release lever Rider 13 C, Rider 16 CClutch control, rear axle Clutch control, front axleBefore starting DrivingStart the engine IMPORTANT INFORMATIONConnecting the jump leads Starting the engine with a weak batteryRemove the cables in the reverse order WARNING! Never run the engine indoors, in2 For Rider 13 C, Rider 16 AWD and Rider 16 C Driving the Rider3 For Rider 11 R and Rider 11 C DrivingStop the engine Cutting tipsStarting on a slope, manual gearbox. Rider 11 R and Rider 11 C WARNING! Clear the lawn from stones andMaintenance schedule MaintenanceDaily maintenance WARNING! No service procedures must beRemoving of the machine hoods CleaningEngine cover Front coverAdjusting the brake Rider 11R and Rider 11 C Checking and adjusting the steering wiresChecking the brake Rider 11 R and Rider 11 C MaintenanceAdjusting the parking brake Rider AWD Adjusting the parking brake Rider 13 C, Rider 16 CAdjusting the throttle wire WARNING! A poorly adjusted brake canIMPORTANT INFORMATION Replacing the air ﬁlterMaintenance Controlling the acid level in a dry- charged battery Replacement of fuel ﬁlterWARNING! Procedures on contact with acid Checking the fuel pump’s air ﬁlterFuses Ignition systemReplacing the spark plug MaintenanceMaintenance Check the safety system28 - English MaintenanceRider 16 AWD when the engine is running. Mind your ﬁngers Checking and adjustment of the cutting unit’s ground pressureChecking the engine’s cooling air intake Checking the cutting unit’s parallelismService position for the cutting unit Adjusting the parallelism of the cutting unitPlacing in the service position Rider 11 C, 13 C, 16 C, 16 AWDMaintenance Restoring from service positionRemoving the BioClip plug Checking the bladesRider 11 C, 13 C, 16 C, 16 AWD Rider 11 RChecking the engine’s oil level LubricationReplacing the engine oil WARNING! Engine oil can be very hot if it isLubrication Rider 11 R and Rider C Lubricating the belt adjusterGeneral lubrication Rider 16 AWDProcedure Troubleshooting scheduleProblem Storage ServiceWinter storage GuardDimensions TECHNICAL DATAEngine Electrical systemTECHNICAL DATA Rider 13 CDimensions EngineTECHNICAL DATA Rider 16 CDimensions EngineTECHNICAL DATA EC-declaration of conformity Applies to Europe onlyPage ´z+S!¶6¶¨ ´z+S!¶6¶¨ Page ´z+S!¶6¶¨ ´z+S!¶6¶¨ 1151019-26