Rider 16 C AWD
Rider 11 R Rider 11 C
Rider 13 C
Rider 16 C
CONTENTS
CONTENTS
Contents
Service journal
Driving and transport on public roads
INTRODUCTION
Dear Customer
Towing
Serial Number
Good service
INTRODUCTION
Pre-delivery service
Service journal
After the first 8 hours
KEY TO SYMBOLS
Symbols
Check the hydrostat’s oil level Lift up the cutting unit
KEY TO SYMBOLS
Starting instructions Check the engine’s oil level
Apply and lock the parking brake If the engine is cold, use the choke
Insure your Rider
SAFETY INSTRUCTIONS
Safety instructions
General use
WARNING! You must use approved personal
Driving on slopes
This is what you do
IMPORTANT INFORMATION
Children
Maintenance
WARNING! The battery contains lead and
WARNING! The engine and the exhaust
SAFETY INSTRUCTIONS
Transport
IMPORTANT INFORMATION
WHAT IS WHAT?
Location of the controls
Clutch pedal Rider 11R and Rider 11 C
PRESENTATION
Presentation
Brake pedal / Parking brake
Cutting unit
Cutting height adjustment lever
Exercise care and refuel outdoors see safety instructions
Lifting lever for the cutting unit
Clutch control, rear axle
Release lever Rider 13 C, Rider 16 C
Release lever Rider 16 AWD
Clutch control, front axle
Start the engine
Driving
Before starting
IMPORTANT INFORMATION
Remove the cables in the reverse order
Starting the engine with a weak battery
Connecting the jump leads
WARNING! Never run the engine indoors, in
3 For Rider 11 R and Rider 11 C
Driving the Rider
2 For Rider 13 C, Rider 16 AWD and Rider 16 C
Driving
Starting on a slope, manual gearbox. Rider 11 R and Rider 11 C
Cutting tips
Stop the engine
WARNING! Clear the lawn from stones and
Daily maintenance
Maintenance
Maintenance schedule
WARNING! No service procedures must be
Engine cover
Cleaning
Removing of the machine hoods
Front cover
Checking the brake Rider 11 R and Rider 11 C
Checking and adjusting the steering wires
Adjusting the brake Rider 11R and Rider 11 C
Maintenance
Adjusting the throttle wire
Adjusting the parking brake Rider 13 C, Rider 16 C
Adjusting the parking brake Rider AWD
WARNING! A poorly adjusted brake can
Maintenance
Replacing the air filter
IMPORTANT INFORMATION
WARNING! Procedures on contact with acid
Replacement of fuel filter
Controlling the acid level in a dry- charged battery
Checking the fuel pump’s air filter
Replacing the spark plug
Ignition system
Fuses
Maintenance
Check the safety system
Maintenance
Rider 16 AWD
Maintenance
28 - English
Checking the engine’s cooling air intake
Checking and adjustment of the cutting unit’s ground pressure
when the engine is running. Mind your fingers
Checking the cutting unit’s parallelism
Placing in the service position
Adjusting the parallelism of the cutting unit
Service position for the cutting unit
Rider 11 C, 13 C, 16 C, 16 AWD
Restoring from service position
Maintenance
Rider 11 C, 13 C, 16 C, 16 AWD
Checking the blades
Removing the BioClip plug
Rider 11 R
Replacing the engine oil
Lubrication
Checking the engine’s oil level
WARNING! Engine oil can be very hot if it is
General lubrication
Lubricating the belt adjuster
Lubrication Rider 11 R and Rider C
Rider 16 AWD
Problem
Troubleshooting schedule
Procedure
Winter storage
Service
Storage
Guard
Engine
TECHNICAL DATA
Dimensions
Electrical system
Dimensions
Rider 13 C
TECHNICAL DATA
Engine
Dimensions
Rider 16 C
TECHNICAL DATA
Engine
EC-declaration of conformity Applies to Europe only
TECHNICAL DATA
Page
´z+S!¶6¶¨ ´z+S!¶6¶¨
Page
1151019-26
´z+S!¶6¶¨ ´z+S!¶6¶¨