Manuals / Carrier / Household Appliance / Air Conditioner

Carrier 48EW, 48EY024-068, 48AW, 48AY020-060, 48EK, 48AK Base Unit Dimensions — 48EJ,EK054-068

Models: 48EJ 48AJ 48AK 48EK 48AY020-060 48AW 48EY024-068 48EW

1 118

Download 118 pages 46.64 Kb

Page 15

Fig. 13 — Base Unit Dimensions — 48EJ,EK054-068

NOTES:

1.Weights include economizer (standard).

2. Center of Gravity.

3.Do not locate adjacent units with flue discharge facing econo- mizer inlet.

Min Clearances to be:

Adjacent Units: 15′-0″[4572].

Top of Units: No Overhang.

Condenser Coil: 4′-0″[1219].

Economizer Side: 6′-0″[1829].

Heat Side: 4′-0″[1219].

Filter Access Side: 15′-0″[4572]. (For removal of evaporator coil.)

4.For smaller service and operational clearances contact Carrier Application Engineering Department.

5.Bottom ducts designed to be attached to accessory roof curb. If unit is mounted on dunnage, it is recommended the ducts must be supported by cross braces as done on accessory roof curb.

6.Base unit weights include outdoor air hoods and filters (indoor fan motor is not included). Add indoor motor, FIOPs and acces- sories for total operating weight.

7.VAV motor weights include indoor motor, VFD, compressor electric unloaders, VFD transducer and associated wiring.

8.Dimensions in are in inches [mm].

15

BASE UNIT WEIGHTS (See Note 6) lbs (kg)

			054			058			064	068
	48EJD/EKD		6805 (3087)			7055 (3200)			7305 (3314)	7480 (3393)
		48EJE	7045 (3196)			7295 (3309)			7545 (3422)	7720 (3502)

	CENTER OF GRAVITY				% OF TOTAL WEIGHT
UNIT SIZE	Inches		Millimeters		AT EACH CORNER
	A	B	A	B	1	2	3	4
48EJD/EKD054	130.9	46.9	3325	1192	22.4	19.6	27.0	30.9
48EJE054	133.8	47.4	3397	1204	23.1	19.8	26.3	30.7
48EJD/EKD058	132.1	47.5	3354	1207	22.9	19.5	26.5	31.1
48EJE058	139.5	49.6	3544	1260	25.3	19.6	24.1	31.1
48EJD/EKD064	125.3	45.2	3181	1149	20.7	19.6	29.1	30.7
48EJE064	132.2	47.2	3359	1199	22.8	19.7	26.7	30.8
48EJD/EKD068	127.7	46.6	3242	1184	21.7	19.3	27.7	31.2
48EJE068	134.7	48.6	3422	1235	23.9	19.4	25.4	31.3

Fig. 13 — Base Unit Dimensions — 48EJ,EK054-068

Image 15

Carrier 48EW, 48EY024-068, 48AW, 48AY020-060, 48EK, 48AK, 48AJ specifications Base Unit Dimensions — 48EJ,EK054-068

Contents

Step 11 — Position Power Exhaust/Barometric CONTENTSSAFETY CONSIDERATIONS INSTALLATION Step 1 — Provide Unit SupportStep 4 — Make Unit Duct Connections Page Page Page NOTES Fig. 5 - Base Unit Dimensions - 48AJ,AK020-030 Fig. 6 — Base Unit Dimensions — 48AJ,AK035-050 Fig. 7 — Base Unit Dimensions — 48AJ,AK060 Fig. 8 — Base Unit Dimensions — 48AW,AY020-030 Fig. 9 — Base Unit Dimensions — 48AW,AY035-050 Fig. 10 — Base Unit Dimensions — 48W,AY060 Fig. 11 — Base Unit Dimensions — 48EJ,EK024-034 Fig. 12 — Base Unit Dimensions — 48EJ,EK038-048 Fig. 13 — Base Unit Dimensions — 48EJ,EK054-068 Fig. 14 — Base Unit Dimensions — 48EW,EY024-034 Fig. 15 — Base Unit Dimensions — 48EW,EY038-048 Fig. 16 — Base Unit Dimensions — 48EW,EY054-068 Fig. 17 — Rigging Information Fig. 17 — Rigging Information cont Table 1A — Physical Data — 48AJ,AK,AW,AY Units UNIT 48AJ,AK,AW,AY Table 1B — Physical Data — 48EJ,EK,EW,EY Units UNIT 48EJ,EK,EW,EY UNIT 48EJ,EK,EW,EY Table 2 — Operating Weights 48AJ,AK,AW,AY Units48EJ,EK,EW,EY Units Table 3 — Evaporator Fan Motor Data Fig. 18 — Air Distribution — Thru-the-BottomFig. 19 — Air Distribution — Thru-the-Side Step 5 — Install Flue Hood Table 4 — 48A,E Series Staged Gas Implementation Fig. 23 — Field Gas PipingTable 6 - Thermistor Designations Fig. 24 — Supply-AirThermistor Connections Fig. 26 — Field Control Remote Start/Stop Fig. 25 — Indoor Air Quality Sensor ConfigurationStep 9 - Make Electrical Connections Fig. 27 — Control Board Diagram Table 7 — Electrical Data — 48AJ,AK,AW,AY Units UNIT SIZE 30.8/28.0 236.3/230.9 Table 8 — Electrical Data — 48EJ,EK,EW,EY Units 30.8 0.96 UNIT Fig. 28 - Field Power Wiring Connections LEGEND Thermostat Wiring CV Only- Install a Carrier-approvedaccessory thermostat assembly per current price pages according to the installation instructions included with the ac- cessory or these instructions. Locate the thermostat on a solid interior wall in the conditioned space to sense the average temperature LEGEND Table 9 — CCN Connection Approved Shielded Cables Fig. 32 — Field Control Thermostat WiringFig. 33 — Field Control Temperature Sensor Wiring CV or VAV UnitsStep 10 — Make Outdoor-AirInlet Adjustments Fig. 34 - Space Temperature Averaging WiringFig. 35 — Field HIR Heat Interlock Relay Wiring Fig. 37 - Economizer Hood Assembly Fig. 36 — Adding Seal Strip to Top of Hood SidesRight Side/Center Economizer Hood Shown Fig. 40 — Adding Foam Strip to Cross Member Fig. 38 — Adding Seal Strip to Sides of Hood TopMounting Flange Fig. 39 — Adding Seal Strip to Back of Hood TopFig. 44 — Mounting Angle With Tabs Attached to Attached to Filter Track AssemblyFilter Track Assembly Fig. 43 - Mounting Angle Without TabsFig. 47 - Wiring Connections for Solid-State Enthalpy Control HH57AC077Save screws CURVE Fig. 49 - Economizer DetailsCONTROL CONTROL POINT48AJ,AK,AW,AY060 and 48EJ,EK,EW,EY054-068 Fig. 51 - Pressure Transducer LocationsFig. 52 - Motormaster III Control Baffle Details Fig. 53A — Motormaster III Sensor Location48AJ,AK,AW,AY020-030and 48EJ,EK,EW,EY024-034 48AJ,AK,AW,AY040, 050 and 48EJ,EK,EW,EY048 Fig. 53B — Motormaster III Sensor Location48AJ,AK,AW,AY035 and 48EJ,EK,EW,EY038 Fig. 53C — Motormaster III Sensor LocationFig. 54 — Side Return Air Conversion Step 13 — Field ModificationsFig. 56 — Wiring Field-SuppliedUnloaders for Constant Volume UnitsSTART-UP Fig. 57 — Toshiba TOSVERT130-E3VFD Factory-InstalledJumpers13.Replace jumper across terminals ST and CC 13.Replace jumper across terminals R and CC Optional Field Wiring LEGEND Typical Factory WiringSee below for building pressure to signal level Table 17 — DIP Switch Configuration Table 18 — DIP Switch Factory Settings AIRFLOW AIRFLOW AIRFLOW 1.06 2.15 3.18 4.81 AIRFLOW AIRFLOW AIRFLOW AIRFLOW AIRFLOW AIRFLOW Table 34 — Air Quality Limits Table 33 — Motor LimitationsSequence of Operation Table 36 - Software Control Link Points Table 35 — User Defined Set PointsThe Time Guard function maintains a minimum off time of 5 minutes, a minimum ON time of 10 seconds, and a minimum delay before starting the second compressor of 10 seconds Fig. 59 — Heat Interlock Relay Wiring Table 38 — Stage Gas System Inputs/Outputs Table 37 — Staged Gas System ComponentsTable 39 — Navigator Display Menu Structure Fig. 60 — Navigator DisplayFig. 61 — Space Temperature Reset Wiring Table 40 — Occupied Heat and Morning Warm-UpOperation and Controlling Factors Fig. 62 - Field-SuppliedSmoke Detector Wiring Table 41 — Smoke Control Modes Table 42 — Cooling Capacity Staging Table, CVUnits with 2 Compressors SERVICE Fig. 64 — Spark Gap AdjustmentFig. 63 — Door Latch Fig. 66 — Gas Heat Section Details Fig. 65 — Typical Gas Heating SectionFig. 67 — Evaporator-FanAlignment and Adjustment LubricationFig. 68 — Evaporator Fan Coupling Condenser-FanAdjustment Evaporator Fan Service and ReplacementBelt Tension Adjustment — To adjust belt tension Evaporator-FanMotor Replacement48EJ,EK,EW,EY024-034 Gas Valve AdjustmentFig. 71 — Cooling Charging Chart Fig. 72 — Cooling Charging Chart48AJ,AK,AW,AY020-060 Fig. 73 — Cooling Charging ChartFig. 74 — Cooling Charging Chart 48EJ,EK,EW,EY054-068Protective Devices LEGEND for Fig. 77-83— Typical Wiring SchematicsTABLE 1A Fig. 78 — Typical 48EK VAV 24-VControl Circuit Fig. 79 — Typical CV 24-VControl Circuit Fig. 80 — Typical 48EK VAV 115-VControl Circuit Fig. 81 — Typical 48EJ CV 115-VControl Circuit Page Page TROUBLESHOOTING LEGEND FPS — Freeze Protection SwitchHPS - High-PressureSwitch LPS - Low-PressureSwitchcompressor LEGEND FPS — Freeze Protection Switch HPS — High-PressureSwitchLPS — Low-PressureSwitch 8-Pass LEGEND FPS — Freeze Protection Switch HPS — High-PressureSwitchLPS — Low-PressureSwitch LEGEND HPS — High-PressureSwitch LPS — Low-PressureSwitchTXV — Thermostatic Expansion Valve TXV — Thermostatic Expansion Valve HPS - High-PressureSwitchLPS — Low-PressureSwitch LEGENDLEGEND HPS — High-PressureSwitch LPS — Low-PressureSwitchTXV — Thermostatic Expansion Valve LEGEND HPS — High-PressureSwitch LPS — Low-PressureSwitchTXV — Thermostatic Expansion Valve Fig. 94 — IGC Control Heating and Cooling LEGEND IDM — Induced-DraftMotorIGC — Integrated Gas Unit Controller Table 45 — Control Board LED Alarms Table 44 - IGC Control Board LED AlarmsPage CALL FOR FREE CATALOG SERVICE TRAININGELECTRICAL START-UPCHECKLISTTEMPERATURES PRE-START-UPGENERAL