Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 210 C manual Installation, Carry out the installation in the following steps

Models: 210 C

1 48

Download 48 pages 61.71 Kb

Page 15

3. INSTALLATION

3. Installation

This chapter describes how you install Husqvarna Automower™. Before starting the installation read the previous chapter 2. Presentation.

Read the whole of this chapter too before starting the installation. How the installation is made also affects how well Automower will work. It is therefore important to plan the installation carefully.

Planning is simplified if you make a sketch of the working area, including all obstacles. This makes it easier to see how the boundary wire should ideally be placed. Draw how the boundary wire is to be routed on the sketch.

Carry out the installation in the following steps:

3.1Preparations.

3.2Installation of the loop generator/charger

3.3Charging the battery.

3.4Installation of the boundary wire.

3.5Connecting the boundary wire.

3.6Checking the installation.

3.7Linking Automower™ to the loop generator/charger

In order to carry out a complete start-up of Automower the loop generator/charger and boundary wire must be connected and the mower linked to the loop generator/charger. If you would like to start the mower without having completed the full boundary installation, you can connect a temporary short loop around the mower.

16 - English

Image 15

Husqvarna 210 C manual Installation, Carry out the installation in the following steps

Contents

HUSQVARNA AUTOMOWER 210 C OPERATOR’S MANUAL TABLE OF CONTENTS 4 - English TABLE OF CONTENTSIMPORTANT INFORMATION 1. Introduction and safety1. INTRODUCTION AND SAFETY 1.1 Introduction1. INTRODUCTION AND SAFETY 1.2 Symbols on Automower1. INTRODUCTION AND SAFETY 1.3 Symbols in the Operator’s ManualXxxxxx xxxxx xxxx xxxx xxxxx IMPORTANT INFORMATION Xxxxxx xxxxx xxxx xxxx xxxxx1. INTRODUCTION AND SAFETY 1.4 Safety instructionsMaintenance Transport1. INTRODUCTION AND SAFETY 2. PRESENTATION 2. Presentation2.1 Automower, what’s what? 2. PRESENTATIONThe numbers in the picture correspond to 2. PRESENTATION 2.2 Function of AutomowerCapacity Mowing technique3012-422 2. PRESENTATION2. PRESENTATION Working method2.3 One Automower in several gardens Movement pattern2. PRESENTATION 3. Installation 3. INSTALLATIONCarry out the installation in the following steps 3.2 Installation of the loop generator/charger 3.1 Preparations3. INSTALLATION 3. INSTALLATION 3.3 Charging the batteryInstallation and connecting the loop generator/charger Automower cannot be used before the installation is complete3.4 Installation of the boundary wire Best position for the boundary wire3. INSTALLATION 3. INSTALLATION 30 cmBoundaries for the working area 10 cm3. INSTALLATION Boundaries within the working areaSecondary areas Slopes3. INSTALLATION Laying out the boundary wire 3. INSTALLATIONIMPORTANT INFORMATION 3. INSTALLATION Laying the boundary wire in towards the loop generator/chargeris not a satisfactory splice. Soil moisture will Joining the boundary wireTwisted cables, or a screw terminal chock-block, insulated with insulation tape3. INSTALLATION 3.5 Connecting the boundary wire3.6 Checking the installation 3.7 Linking Automower to the loop generator/charger3. INSTALLATION 4.1 Starting Automower Read the safety instructions before you start your Automower4. Use 4. USE4. USE 4.4 Switching off Automower4.5 Adjusting the cutting height 4.3 Restart4. USE 4.6 Changing the PIN code4. USE 4.7 SoundsSound Significance5.2 Numbers 5. Control panel5. CONTROL PANEL 5.1 Select5.3 Main switch 5.4 Indicator lamps5. CONTROL PANEL 6. GARDEN EXAMPLE Proposed installationProposals for installation 6. Garden exampleProposals for installation 6. GARDEN EXAMPLEGarden with a steep incline 30 % that IMPORTANT INFORMATION 7. Maintenance7. MAINTENANCE 7.1 BatteryAutomower 7.3 Service7.4 Cleaning 7.2 Winter storageWheels IMPORTANT INFORMATION Do not use running water when cleaningUnderframe and blade disc Chassis7. MAINTENANCE Always use originalblades and screws when replacing7.5 Replacing the blades Body40 - English 7. MAINTENANCE5. Unscrew the blade. Use a straight slot or cross-tip screwdriver 7. Screw tight the new bladeFault message 8. Trouble shooting8. TROUBLE SHOOTING 8.1 Fault messagesCause 8. TROUBLE SHOOTINGFault message FlashesAction 8.2 Fault symptomSymptom Causeinformation 9. Technical data9. TECHNICAL DATA 10. EnvironmentalSerial number Personal code Dealer Dealer’s telephone number 11. EU declaration of conformity11. EU DECLARATION OF CONFORMITY EU Declaration of Conformity only applies to Europe46 - English 11. EU DECLARATION OF CONFORMITY12. INDEX 12. Index12. INDEX Use AutomowerWhat’s what Automower