Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 11, 39765 Lever for adjustment of cutting height, Seat, Fuelling, Rider, Presentation

Models: 11 Bio 11 13 Bio 39765

1 47

Download 47 pages 43.8 Kb

Page 14

Image 14

PRESENTATION

Lever for adjustment of cutting height

With this lever the cutting height can be adjusted to 9 different positions.

Cutting unit with rear ejection,	40-90 mm.
BioClip cutting unit,	45-95 mm.

Rider 13

Seat

The seat has a jointed attachment on the front edge and can be tipped forward.

The seat can also be adjusted lengthways.

Release the knobs under the seat and adjust it forwards or backwards to the required position.

Lock the adjustment with the wheels.

Fuelling

The engine should be run on 85 octane (or higher) unleaded petrol/gasoline (no added oil). Environ- mentally adapted alkylate fuel, such as Aspen, is also recommended.

!WARNING!

Petrol/gasoline is highly inflammable. Observe care and fill up with fuel outdoors (see safety instructions).

English – 13

Page 14

Image 14

Husqvarna 39765, 13 Bio, 11 Bio manual Lever for adjustment of cutting height, Seat, Fuelling, Rider, Presentation

Contents

Operator´s manual 101Rider 11/13 Rider 11 Bio/13 Bio IMPORTANT INFORMATION CONTENTS Operator’s Manual for Rider 11 and RiderRider 11 Bio and Rider 13 Bio Travel and transport on public roads INSTRUCTIONDear customer TowingSerial number SAFETY INSTRUCTIONSGood service EngineEXPLANATION OF SYMBOLS Clear the area from stones etc. before cutting General useRead the instructions before starting the machine Never carry passengersDo as follows Be extra careful when driving on slopesDriving on slopes Cut slopes upwards and downwards, not sidewaysKeep children away from the mowing area MaintenanceChildren Never allow children to drive the machinebattery can explode and cause severe injuries Clean the machine regularly from grass, leaves and other wasteSAFETY INSTRUCTIONS Avoid overfilling. If fuel has been spilt on theLocation of the controls PRESENTATIONPresentation Clutch pedal PRESENTATION RIDER 11 / 11 BIOThrottle and Choke lever Brake pedal / Parking brakeParking brake PRESENTATION RIDER 13/13 BIOSpeed limiter Throttle and Choke leverRider 11 Bio and Rider 13 Bio have a twin-blade Cutting unitLift lever for cutting unit Lifting of the cutting unit transport positionFuelling Lever for adjustment of cutting heightSeat RiderStarting the engine DRIVINGBefore starting RiderDRIVING Cold engineWarm engine 5. Set the throttle control midway between position 1 andFor Rider 11 and Rider 11 Bio Driving the machine2. For Rider 13 and Rider 13 Bio The clutch must be used for each gear changeDRIVING Cutting tipsMowing pattern IMPORTANT INFORMATIONRelease lever Rider 13 and Rider 13 Bio Hill start, manual gearboxStopping the engine DRIVINGMaintenance interval MAINTENANCEMaintenance schedule MaintenanceFront hood Rider 11 and Rider Dismantling of the machine hoodsEngine hood Front hood Rider 11 Bio and Rider 13 BioMAINTENANCE Right-hand fenderLeft-hand fender Release the screws in the fender and lift off the fenderChecking and adjustment of the steering wires MAINTENANCEPoorly adjusted brakes can result in reduced braking power Adjusting the brake Rider 11 and Rider 11 BioCheck and adjust the brakes on Rider 13 and Rider 13 Bio Checking the brake Rider 11 and Rider 11 BioMAINTENANCE Checking and adjustment of the throttle wireReplacement of the fuel filter MAINTENANCE Do not use compressed air to clean the paper filterReplacing the air filter IMPORTANT INFORMATIONChecking of the fuel pump’s air filter Check the level of the battery acidProcedures on contact with acid MAINTENANCEMAINTENANCE Inspecting the safety systemRider Rider MAINTENANCE Checking the tyre pressureCheck the engine’s cooling air intake IMPORTANT INFORMATIONChecking the cutting unit’s parallelism MAINTENANCEMAINTENANCE 30 - EnglishPlacing in service position MAINTENANCE RIDER 11 BIO/13 BIOService position for BioClip MAINTENANCE RIDER 11 BIO/13 BIO 5. Disengage the spring from the drive belt tensioning wheelRestoring from service position MAINTENANCE RIDER 11 BIO/13 BIOCutting unit rear ejection Bio Checking the bladesReplacing the break-pin BioClip MAINTENANCEChanging the oil LUBRICATIONCheck the engine’s oil level IMPORTANT INFORMATIONGeneral lubrication Check the transmission’s oil level Rider 13 and Rider 13 BioLubrication of belt tensioner LUBRICATIONCheck that the lock-ring is correctly posi- tioned in the slot Lubrication Rider 11 and Rider 11 BioLubrication of front wheel bearings LUBRICATIONProcedure TROUBLE SHOOTING SCHEDULEProblem Winter storage ServiceSTORAGE Rider TECHNICAL DATADimensions Electrical systemTECHNICAL DATA Rider 11 BioRider 13 Bio DimensionsEU declaration of conformity Only applies to Europe Directive 89/392/EEC, Annex II, AWork done SERVICEJOURNAL RIDER 11/13Pre-delivery service Date, mileage, stamp, signWork done SERVICEJOURNAL´*3/r¶69¨ Date, mileage, stamp, signPage 2000W50 ´*3/r¶69¨