Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna 13 Bio Dismantling of the machine hoods, Engine hood, Front hood Rider 11 and Rider

Models: 11 Bio 11 13 Bio 39765

1 47

Download 47 pages 43.8 Kb

Page 21

Image 21

MAINTENANCE

Dismantling of the machine hoods

Engine hood

The engine is accessible for servicing when the engine hood is lifted up.

Tilt the seat forward, release the rubber strap under the seat, and tilt the hood backwards.

Front hood Rider 11 and Rider 13

Release the screws in the front hood (3) and lift off the hood.

Front hood Rider 11 Bio and Rider 13 Bio

Release the catch and lift off the hood.

20 – English

Page 21

Image 21

Husqvarna 13 Bio, 39765 Dismantling of the machine hoods, Engine hood, Front hood Rider 11 and Rider, Maintenance, English

Contents

101 Rider 11/13 Rider 11 Bio/13 BioOperator´s manual CONTENTS Operator’s Manual for Rider 11 and Rider Rider 11 Bio and Rider 13 BioIMPORTANT INFORMATION Dear customer INSTRUCTIONTravel and transport on public roads TowingGood service SAFETY INSTRUCTIONSSerial number EngineEXPLANATION OF SYMBOLS Read the instructions before starting the machine General useClear the area from stones etc. before cutting Never carry passengersDriving on slopes Be extra careful when driving on slopesDo as follows Cut slopes upwards and downwards, not sidewaysChildren MaintenanceKeep children away from the mowing area Never allow children to drive the machineSAFETY INSTRUCTIONS Clean the machine regularly from grass, leaves and other wastebattery can explode and cause severe injuries Avoid overfilling. If fuel has been spilt on thePRESENTATION PresentationLocation of the controls Throttle and Choke lever PRESENTATION RIDER 11 / 11 BIOClutch pedal Brake pedal / Parking brakeSpeed limiter PRESENTATION RIDER 13/13 BIOParking brake Throttle and Choke leverLift lever for cutting unit Cutting unitRider 11 Bio and Rider 13 Bio have a twin-blade Lifting of the cutting unit transport positionSeat Lever for adjustment of cutting heightFuelling RiderBefore starting DRIVINGStarting the engine RiderWarm engine Cold engineDRIVING 5. Set the throttle control midway between position 1 and2. For Rider 13 and Rider 13 Bio Driving the machineFor Rider 11 and Rider 11 Bio The clutch must be used for each gear changeMowing pattern Cutting tipsDRIVING IMPORTANT INFORMATIONStopping the engine Hill start, manual gearboxRelease lever Rider 13 and Rider 13 Bio DRIVINGMaintenance schedule MAINTENANCEMaintenance interval MaintenanceEngine hood Dismantling of the machine hoodsFront hood Rider 11 and Rider Front hood Rider 11 Bio and Rider 13 BioLeft-hand fender Right-hand fenderMAINTENANCE Release the screws in the fender and lift off the fenderMAINTENANCE Checking and adjustment of the steering wiresCheck and adjust the brakes on Rider 13 and Rider 13 Bio Adjusting the brake Rider 11 and Rider 11 BioPoorly adjusted brakes can result in reduced braking power Checking the brake Rider 11 and Rider 11 BioChecking and adjustment of the throttle wire Replacement of the fuel filterMAINTENANCE Replacing the air filter Do not use compressed air to clean the paper filterMAINTENANCE IMPORTANT INFORMATIONProcedures on contact with acid Check the level of the battery acidChecking of the fuel pump’s air filter MAINTENANCEInspecting the safety system Rider RiderMAINTENANCE Check the engine’s cooling air intake Checking the tyre pressureMAINTENANCE IMPORTANT INFORMATIONMAINTENANCE Checking the cutting unit’s parallelism30 - English MAINTENANCEMAINTENANCE RIDER 11 BIO/13 BIO Service position for BioClipPlacing in service position 5. Disengage the spring from the drive belt tensioning wheel MAINTENANCE RIDER 11 BIO/13 BIOMAINTENANCE RIDER 11 BIO/13 BIO Restoring from service positionReplacing the break-pin BioClip Checking the bladesCutting unit rear ejection Bio MAINTENANCECheck the engine’s oil level LUBRICATIONChanging the oil IMPORTANT INFORMATIONLubrication of belt tensioner Check the transmission’s oil level Rider 13 and Rider 13 BioGeneral lubrication LUBRICATIONLubrication of front wheel bearings Lubrication Rider 11 and Rider 11 BioCheck that the lock-ring is correctly posi- tioned in the slot LUBRICATIONTROUBLE SHOOTING SCHEDULE ProblemProcedure Service STORAGEWinter storage Dimensions TECHNICAL DATARider Electrical systemRider 13 Bio Rider 11 BioTECHNICAL DATA DimensionsDirective 89/392/EEC, Annex II, A EU declaration of conformity Only applies to EuropePre-delivery service SERVICEJOURNAL RIDER 11/13Work done Date, mileage, stamp, sign´*3/r¶69¨ SERVICEJOURNALWork done Date, mileage, stamp, signPage ´*3/r¶69¨ 2000W50