Manuals / Husqvarna / Household Appliance / Sewing Machine

Husqvarna 850, 970 manual Starting on slopes, Stopping the engine, Driving

Models: 970

1 36

Download 36 pages 63.29 Kb

Page 20

Image 20

DRIVING

Starting on slopes

1.Apply the parking brake.

2.Push the throttle control to 3/4 position to full throttle position.

3.Push down the clutch and engage first gear.

4.Carefully release the clutch.

5.When the engine begins to drive, release the parking brake.

!WARNING!

Never drive the machine on ground with a slope of more than 15°. Mow slopes upwards and downwards, never across. Avoid sudden changes in direction.

MAX 15°

Stopping the engine

Preferably allow the engine to idle for a minute to obtain normal working temperature before stopping if it has been working hard.

1.Lift up the cutting unit by pulling the lever back to the end position.

2.Pull back the throttle control and move the gear shift to neutral (N).

Turn the ignition key to the STOP position.

STOP START

18 – English

Page 20

Image 20

Husqvarna 850, 970 manual Starting on slopes, Stopping the engine, Driving

Contents

101 Rider 850/970Operator´s manual R I D E RPage CONTENTSE Operator’s Manual for Rider 850 Rider SAFETY INSTRUCTIONS Safe operation practices for ride-on mowersI. General operation II. Slope operationIV. Service Wheel assembly USAPart Package Danger, keep hands and feet awayEXPLANATION OF SYMBOLS General use Read the instructions before starting the machineClear the area from stones etc. before cutting Never carry passengersBe extra careful when driving on slopes Driving on slopesCut slopes upwards and downwards, not sideways SAFETY INSTRUCTIONSMaintenance ChildrenKeep children away from the mowing area Never allow children to drive the machineNever smoke in the vicinity of the battery or the fuel Clean the machine regularly from grass, leaves and other wasteNever drive the machine in an enclosed space SAFETY INSTRUCTIONSLocation of the controls PRESENTATIONEPresentation EPRESENTATION Throttle and Choke leverClutch pedal Brake pedalParking brake Gear shiftCutting unit PRESENTATIONELever for adjustment of cutting height Lift lever for cutting unitLifting of the cutting unit transport position Lowering of the cutting unit cutting positionFuelling PRESENTATIONSeat Starting the engine DRIVINGBefore starting DRIVING 4. Push the throttle control to position 3 chokeDriving the machine DRIVINGDRIVING Cutting tipsMowing pattern DRIVING Starting on slopesStopping the engine MAINTENANCEE Maintenance scheduleEMAINTENANCE Dismantling of the machine hoodsMAINTENANCE Check the engine’s oil levelCheck the engine’s cooling air intake Checking of the fuel pump’s air filterChecking and adjustment of the steering wires EMAINTENANCEAdjusting the brake Check the level of the battery acidCheck the safety system Checking the brakeReplacing the air filter EMAINTENANCEChecking and adjustment of the cutting unit’s ground pressure RiderChecking the cutting unit’s parallelism MAINTENANCE26 - English Adjustment of the cutting unit’s parallelismEMAINTENANCE Dismantling the cutting unit MAINTENANCEChecking the blades Checking the tyre pressureCutting unit on Rider 850 rear ejection EMAINTENANCEChanging the oil Lubrication4. Fit the drain plug and tighten MAINTENANCEChecking and adjustment of the throttle wire Replacement of the fuel filterEMAINTENANCE 30 - EnglishProcedure TROUBLE SHOOTING SCHEDULEProblem Service «*2T6B¬ESTORAGE Winter storageTECHNICAL DATA «*2T6B¬