Pre-delivery service, After the ﬁrst 25 hours | Husqvarna P 520D

Service journal

Pre-delivery service

1Charge the battery for at least 4 hours at max. 3 amp.

2Check coolant level and antifreeze.

3Check and adjust tyre pressure (150 kPa, 1,5 bar, 21,8 PSI).

4Make sure the correct amount of oil is in the cutting unit's bevel gear.

5Check that the right amount of oil is in the engine.

6Check that there is oil in the transmission’s oil tank.

7Fit cutting unit.

8Adjust cutting unit:

Adjust cutting unit so that rear edge is about 6-9 mm higher than front edge.

9Lubricate the universal drive shaft with grease.

10Connect battery.

11Fill with fuel and start engine.

12Check that machine does not move in neutral.

13Check: Forward drive.

Reverse drive.

Operation of blades.

Seat safety switch.

Safety switch for parking brake.

14Tell customer about:

The requirement and advantages of servicing the machine according to the service plan

Servicing and the inﬂuence of this journal on the second-hand value of the machine.

The transmission guarantee is only valid if the synchronisation of the front and rear wheels has been checked and adjusted in compliance with

the service schedule. The system will be damaged if synchronisation is not carried out.

At temperatures below 0 ° C, the machine must be warmed up for at least 10 minutes for the hydraulic oil and transmission to get hot.

Otherwise there is a risk of the transmission breaking down thereby reducing the service life of the transmission.

Range of applications for BioClip.

Complete proof of sale etc.

Pre-delivery service carried out. No outstanding problems. Certiﬁed:

______________________________________________

Date, mileage, stamp, signature

After the ﬁrst 25 hours

1 Change the engine oil and oil ﬁlter

2 Change the transmission oil and oil ﬁlter

3Check the synchronisation between the front and rear wheels.

English – 3

Image 3

Husqvarna P 520D, P 525D manual Pre-delivery service, After the ﬁrst 25 hours

Contents

English 520D 525D Contents After the ﬁrst 25 hours Pre-delivery service Towing IntroductionDear Customer Driving and transport on public roads Good service Symbols KEY to Symbols Location of the controls What is WHAT? General use Safety InstructionsSafety instructions Insure your Rider This is what you do Driving on slopes Children Maintenance Transport Presentation Lowering the Unit Mowing Position Adjusting the cutting heightLever for hydraulic lift of attachments Lifting the Cutting Unit Transport Position Fueling Lights and power outletSafety instructions Seat Bypass valves Instrument panel Auxiliary lift system Rops Roll Over Protective Structure Start the engine Starting and driving when coldStarting Engine Before starting Starting the engine with a weak battery Connecting the jump leadsRemove the cables in the reverse order Stop the engine DrivingDriving the Rider Braking Other objects which can be thrown out by the blades Cutting tips Maintenance schedule 800Starting Completed Cleaning Removing of the machine hoodsChecking the engine’s cooling air intake Change pump and alternator belt Adjustment of pump and alternator beltAdjusting the parking brake Replacement of fuel ﬁlter Replacing the air ﬁlter Cleaning the air ﬁlterCleaning the engine and mufﬂer Cleaning the ﬁlter cover Checking the tyre pressure Check the safety systemReplacing the light bulbs Main fuse Check the battery Cutting Unit ComponentsFitting the cutting head Trapping your hand Pins are loosened. Observe caution to avoidRemoving the cutting unit Lift arms move with great force when Placing in the service position Service position for the cutting unit Cutting height and tilt angle adjustment Restoring from service positionCutting height Tilt angle Replacing the cutting unit beltsChecking the blades Removing the BioClip plug Change PTO belts Adjustment of PTO belts Glycol Water Freezing point Change coolant General Lubrication schedule Universal drive shaft joints AccessoriesPivot wheel bearings Cutting unit bevel gear Joint bearing Drive shaft front support bearingDrive shaft rear support bearing Steering cylinder Drained directly after stopping the engine Changing the oil ﬁlterCheck the hydraulic system oil level Replacing the engine oil Lubricating the cables Knobs for setting the cutting heightLubricate the parking brake wire Driver seat Engine does not run smoothly Problem Procedure Engine does not startEngine seems to have no power Starter motor does not turn over the engine Battery does not charge Engine overheatsUneven mowing Electrical System Wiring diagram P 520D Electrical System Electrical System Electrical System Electrical System Electrical System Wiring diagram P525 D Electrical System Electrical System Electrical System Electrical System Electrical System Service Winter storageGuard Technical Data EC-declaration of conformity Applies to Europe only Sound levels see noteVibration levels see note Original instructions 1154837-26 ´z+Vsh¶6¨ ´z+Vsh¶6¨