Manuals / Husqvarna / Lawn and Garden / Lawn Mower

Husqvarna P 520D, P 525D manual Lubrication schedule, General

Models: P 525D P 520D

1 56

Download 56 pages 51.4 Kb

Page 33

Image 33

Lubrication

Lubrication schedule

Legend for the lubrication schedule

Filter replacement

Oil change

Level check

Grease nipple

Oil can

Check belts, condition and belt tension

General

Remove the ignition key to prevent unintentional movements during lubrication.

When lubricating with an oilcan, it ought to be ﬁlled with engine oil.

When lubricating with grease, unless otherwise stated, grease 503 98 96-01 or another chassis or ball bearing grease offering good corrosion protection shall be used.

If the machine is used daily it should be lubricated twice a week.

Wipe away excess grease after lubrication.

It is important to avoid getting lubricant on the belts or the drive surfaces on the belt pulleys. Should this happen, attempt to clean them with spirits. If the belt continues to slip after cleaning with spirits, it must be replaced.

Petrol or other petroleum products must not be used to clean belts.

Belt replacement

English – 33

Page 33

Image 33

Husqvarna P 520D, P 525D manual Lubrication schedule, General

Contents

English 520D 525DContents After the ﬁrst 25 hours Pre-delivery serviceDear Customer IntroductionDriving and transport on public roads TowingGood service Symbols KEY to SymbolsLocation of the controls What is WHAT?Safety instructions Safety InstructionsInsure your Rider General useThis is what you do Driving on slopesChildren MaintenanceTransport Presentation Lever for hydraulic lift of attachments Adjusting the cutting heightLifting the Cutting Unit Transport Position Lowering the Unit Mowing PositionSafety instructions Lights and power outletSeat FuelingBypass valves Instrument panelAuxiliary lift system Rops Roll Over Protective StructureStarting Engine Starting and driving when coldBefore starting Start the engineStarting the engine with a weak battery Connecting the jump leadsRemove the cables in the reverse order Driving the Rider DrivingBraking Stop the engineOther objects which can be thrown out by the blades Cutting tipsMaintenance schedule 800Starting Completed Cleaning Removing of the machine hoodsChecking the engine’s cooling air intake Adjusting the parking brake Adjustment of pump and alternator beltReplacement of fuel ﬁlter Change pump and alternator beltCleaning the engine and mufﬂer Cleaning the air ﬁlterCleaning the ﬁlter cover Replacing the air ﬁlterReplacing the light bulbs Check the safety systemMain fuse Checking the tyre pressureCheck the battery Cutting Unit ComponentsFitting the cutting head Removing the cutting unit Pins are loosened. Observe caution to avoidLift arms move with great force when Trapping your handPlacing in the service position Service position for the cutting unitCutting height and tilt angle adjustment Restoring from service positionCutting height Checking the blades Replacing the cutting unit beltsRemoving the BioClip plug Tilt angleChange PTO belts Adjustment of PTO beltsGlycol Water Freezing point Change coolantGeneral Lubrication schedulePivot wheel bearings AccessoriesCutting unit bevel gear Universal drive shaft jointsDrive shaft rear support bearing Drive shaft front support bearingSteering cylinder Joint bearingCheck the hydraulic system oil level Changing the oil ﬁlterReplacing the engine oil Drained directly after stopping the engineLubricate the parking brake wire Knobs for setting the cutting heightDriver seat Lubricating the cablesEngine seems to have no power Problem Procedure Engine does not startStarter motor does not turn over the engine Engine does not run smoothlyBattery does not charge Engine overheatsUneven mowing Electrical System Wiring diagram P 520D Electrical System Electrical System Electrical System Electrical System Electrical System Wiring diagram P525 D Electrical System Electrical System Electrical System Electrical System Electrical System Service Winter storageGuard Technical Data EC-declaration of conformity Applies to Europe only Sound levels see noteVibration levels see note Original instructions 1154837-26 ´z+Vsh¶6¨ ´z+Vsh¶6¨