Check the battery, Cutting Unit Components | Husqvarna P 525D

Maintenance

Check the battery

WARNING! Lead-acid batteries produce

!explosive gases. Avoid sparks, open ﬂames and smoking close to batteries. Always wear protective glasses in the vicinity of batteries.

The machine is equipped with a maintenance-free battery. The battery has a service window showing different colours.

•White = Charge battery

•Green = OK.

•Red = Change battery.

Clean the battery and holder with soap/water solution.

A discarded or replacement battery should be handled as hazardous waste.

The Cutting Unit Components

The components mentioned are:

4

3

2

9

5

6

Fitting the cutting head

1Place the machine on a ﬂat surface and apply the parking brake.

2Start the engine and lower the lift arms to ﬂoating mode.

!	WARNING! If the help function is engaged,
	the lift arms will move with great force if
	someone releases the lifting lever. Observe
	caution to avoid trapping your hand.

Risk of crush injuries.

3Turn off the motor.

4Fit the universal drive shaft to the cutting unit. Slide the ring sideways to release the quick coupling and the universal drive shaft can be pushed onto the shaft pin.

8 7

1

4

5Make sure the rubber casing is folded over the front universal joint.

1Cotter pin

2Link joint

3Cutting unit bracket

4Clipping height adjusters

5Universal drive shaft with quick connectors

6Attachment point for service position

7Service strut

8Belt cover

9Gear

6Remove the bolts and pins from the link joint on the lift arms.

7Slide in the cutting unit so that the link joint aligns with the opening in the unit.

8Insert the bolts for the link joints and the pins on both sides.

26 – English

Image 26

Husqvarna P 525D, P 520D manual Check the battery, Cutting Unit Components, Fitting the cutting head

Contents

520D 525D English Contents Pre-delivery service After the ﬁrst 25 hours Driving and transport on public roads IntroductionDear Customer Towing Good service KEY to Symbols Symbols What is WHAT? Location of the controls Insure your Rider Safety InstructionsSafety instructions General use Driving on slopes This is what you do Maintenance Children Transport Presentation Lifting the Cutting Unit Transport Position Adjusting the cutting heightLever for hydraulic lift of attachments Lowering the Unit Mowing Position Seat Lights and power outletSafety instructions Fueling Instrument panel Bypass valves Rops Roll Over Protective Structure Auxiliary lift system Before starting Starting and driving when coldStarting Engine Start the engine Remove the cables in the reverse order Starting the engine with a weak batteryConnecting the jump leads Braking DrivingDriving the Rider Stop the engine Cutting tips Other objects which can be thrown out by the blades Starting Completed Maintenance schedule800 Checking the engine’s cooling air intake CleaningRemoving of the machine hoods Replacement of fuel ﬁlter Adjustment of pump and alternator beltAdjusting the parking brake Change pump and alternator belt Cleaning the ﬁlter cover Cleaning the air ﬁlterCleaning the engine and mufﬂer Replacing the air ﬁlter Main fuse Check the safety systemReplacing the light bulbs Checking the tyre pressure Fitting the cutting head Check the batteryCutting Unit Components Lift arms move with great force when Pins are loosened. Observe caution to avoidRemoving the cutting unit Trapping your hand Service position for the cutting unit Placing in the service position Cutting height Cutting height and tilt angle adjustmentRestoring from service position Removing the BioClip plug Replacing the cutting unit beltsChecking the blades Tilt angle Adjustment of PTO belts Change PTO belts Change coolant Glycol Water Freezing point Lubrication schedule General Cutting unit bevel gear AccessoriesPivot wheel bearings Universal drive shaft joints Steering cylinder Drive shaft front support bearingDrive shaft rear support bearing Joint bearing Replacing the engine oil Changing the oil ﬁlterCheck the hydraulic system oil level Drained directly after stopping the engine Driver seat Knobs for setting the cutting heightLubricate the parking brake wire Lubricating the cables Starter motor does not turn over the engine Problem Procedure Engine does not startEngine seems to have no power Engine does not run smoothly Uneven mowing Battery does not chargeEngine overheats Electrical System Wiring diagram P 520D Electrical System Electrical System Electrical System Electrical System Electrical System Wiring diagram P525 D Electrical System Electrical System Electrical System Electrical System Electrical System Guard ServiceWinter storage Technical Data Vibration levels see note EC-declaration of conformity Applies to Europe onlySound levels see note 1154837-26 ´z+Vsh¶6¨ ´z+Vsh¶6¨ Original instructions