Sierra S5832SG installation instructions Block 3 - Armed System Programming cont

Block 3 - Armed System Programming (cont.)

Quick Bypass Enable		Comments
Cmd Loc	006	If enabled, quick bypass allows any user to bypass zones
Default	1	without entering a user code. To bypass a zone, press the
Range	1 - 2	[Bypass] key followed by the 2-digit code for the zone to be
		bypassed.

Options:

1No

2 Yes

Home Arm Exit Delay Enable

Cmd Loc	007
Default	1
Range	1 - 2

Comments	Options:
If enabled, the exit delay (Block 2, CL 003) will start when a	1	No
user presses and holds the [Home] key for two seconds. If	2	Yes
disabled, the exit delay will be ignored and the system will
home arm instantly.

4X Exit Delay Extension Enable Comments Options:

Cmd Loc

Default

Range

008

2

1 - 2

If enabled, the exit delay (Block 2, CL 003) will restart if the	1	No
delay zone is faulted a second or subsequent time during	2	Yes
the exit delay. The exit delay may be restarted up to 4 times.

Chirp-Alert on Exit Fail Comments Options:

Cmd Loc

Default

Range

009

2

1 - 2

If enabled, all sounders (internal and external) will chirp for	1	No
three seconds at the start of the entry delay (Block 2, CL	2	Yes
001 or 002).

Low Battery Arming Comments Options:

Cmd Loc

Default

Range

010

2

1 - 2

If enabled, allows the system to be armed even if the back-	1	No
up battery is low.	2	Yes

Keypad Buzzer During Exit Delay Comments Options:

Cmd Loc

Default

Range

011

2

1 - 2

If enabled, the keypad buzzer sounds during the exit delay.	1	No
The keypad buzzer rate is faster during the last 10 seconds	2	Yes
of the exit delay.

Keypad Buzzer During Entry Delay

Cmd Loc	012
Default	2
Range	1 - 2

Comments

If enabled, the keypad buzzer sounds during the entry de- lay. The keypad buzzer rate is faster during the last 10 seconds of the entry delay.

Options:

1No

2 Yes

Keypad LED Status

Cmd Loc	013
Default	1
Range	1 - 3

Comments

This option controls the zone and status displays of the LED keypad.

NOTE: The Power and Arm LEDs on all keypads oper- ate the same.

Options:

1Always display arm and zone status

2 Status always on while disarmed. If armed, status displayed for 30 secs.

3 Display arm and zone status for 30 seconds following User Code entry.

Cross-Zoning List
Zones:	1 - 8	9 - 16	17 - 24	25 - 32
Cmd Loc	014	015	016	017
Default	0	0	0	0
Range	0 - 255	0 - 255	0 - 255	0 - 255

Comments

If programmed for cross-zoning, any two of the zones listed here must be violated while armed in order for an alarm condition to register.

If the system is divided into areas, both zones in alarm must be within the same area.

NOTE: Fire, delay, and keyswitch zones are ignored if placed on the cross-zone list.

Options:

0	Disabled
1	Zone 1 9 17 25
2	Zone	2	10	18	26
4	Zone	3	11	19	27
8	Zone	4	12	20	28
16	Zone	5	13	21	29
32	Zone	6	14	22	30
64	Zone	7	15	23	31
128	Zone	8	16	24	32

Double-Knock List

Zones:	1 - 8	9 - 16	17 - 24	25 - 32
Cmd Loc	018	019	020	021
Default	0	0	0	0
Range	0 - 255	0 - 255	0 - 255	0 - 255

Comments

Zones listed here must be violated twice (or any two zones must be faulted) within

a30-second period in order for an alarm condition to register.

If the system is divided into areas, the alarms must be within the same area.

NOTE: Fire, delay, and keyswitch zones are ignored if placed on this list.

Options:

0	Disabled
1	Zone 1 9 17 25
2	Zone	2	10 18	26
4	Zone	3	11 19	27
8	Zone	4	12 20	28
16	Zone	5	13 21	29
32	Zone	6	14 22	30
64	Zone	7	15 23	31
128	Zone	8	16 24	32

17