Sierra S5832SG Report Code, Opening Users 1 User #, Report Code, Closing Users 1 User #

Block 5 - Reporting Digits Programming (cont.)

Report Code, Opening (Users 1 - 60)
User #:	1 - 15	16 - 30	31 - 45	46 - 60
Cmd Loc	095	096	097	098
Default	1	1	1	1
Range	0 - 15	0 - 15	0 - 15	0 - 15

Comments

The opening report code is a single-digit code. For two-digit reporting formats, the relative user number (1 - 15) is sent as the second digit. Program the specific Cmd Loc with 0 to disable reporting. Disabling a Cmd Loc disables reporting for all users associated with that location.

Report Code, Closing (Users 1 - 60)
User #:	1 - 15	16 - 30	31 - 45	46 - 60
Cmd Loc	099	100	101	102
Default	1	1	1	1
Range	0 - 15	0 - 15	0 - 15	0 - 15

Comments

The closing report code is a single-digit code. For two-digit reporting formats, the relative user number (1 - 15) is sent as the second digit. Program the specific Cmd Loc with 0 to disable reporting. Disabling a Cmd Loc disables reporting for all users associated with that location.

Report Code, Cancel (Users 1 - 60)
User #:	1 - 15	16 - 30	31 - 45	46 - 60
Cmd Loc	103	104	105	106
Default	0	0	0	0
Range	0 - 15	0 - 15	0 - 15	0 - 15

Comments

The cancel report code is a single-digit code. For two-digit reporting for- mats, the relative user number (1 - 15) is sent as the second digit. Program the specific Cmd Loc with 0 to disable reporting. Disabling a Cmd Loc disables reporting for all users associated with that location.

Report Code, Exit Fail Alarm (Zones 1 - 32) Zones: 1 - 8 9 - 16 17 - 24 25 - 32

Cmd Loc	107	108	109	110
Default	0	0	0	0
Range	0 - 15	0 - 15	0 - 15	0 - 15

Comments

The exit fail report code is a single-digit code which is sent if the exit (delay) zone remains faulted at the end of the exit delay. The alarm is generated in association with the Chirp-Alert Warning (Block 3, CL 009). For two-digit reporting formats, the relative zone number (1 - 8) is sent as the second digit. Program the specific Cmd Loc with 0 to disable reporting. Disabling a Cmd Loc disables reporting for all zones associated with that location.

Report Code, Kidwatch Check-in Failure				Comments
Cmd Loc	111	112		This two-digit code is sent to the central station if the Kidwatch code (user
Default	0	0		#11) is not entered during the Kidwatch period (Block 6, CL 006 - 009).
Range	0 - 15	(All	CL)	Disable the reporting by programming 00 into these Cmd Loc.

Report Code, AC Power Loss

Cmd Loc	113	114
Default	0	1
Range	0 - 15	(All	CL)

Comments

These two-digit codes are used to report AC power failures and restorals. Only the second digit is sent when using single-digit reporting formats.

Report Code, AC Power Restoral

Cmd Loc	115	116
Default	0	1
Range	0 - 15	(All	CL)

Report Code, Low Battery

Cmd Loc	117	118
Default	0	1
Range	0 - 15	(All	CL)

Comments

These two-digit report codes will be sent to indicate a low battery condition or restoral report. When using single-digit reporting formats, only the sec- ond digit will be sent.

Report Code, Low Battery Restoral

Cmd Loc	119	120
Default	0	1
Range	0 - 15	(All CL)

Report Code, Test

Cmd Loc	121	122
Default	0	1
Range	0 - 15	(All CL)

Comments

This two-digit report code will be sent to indicate a system test. When using single-digit reporting formats, only the second digit is sent.

Report Code, Failure to Report (Comm Fail)

Cmd Loc	123	124
Default	0	0
Range	0 - 15	(All	CL)

Comments

These two-digit report codes will be sent to indicate a comm fail (failure to report) condition. The reports are also sent to indicate a comm fail restoral. Only the second digit is sent when using single-digit reporting formats.

Report Code, Fail to Report (Comm Fail) Restoral

Cmd Loc	125	126
Default	0	0
Range	0 - 15	(All CL)

Report Code, Primary Phone Line Cut

Cmd Loc	127	128
Default	0	0
Range	0 - 15	(All Locations)

Comments

These two-digit codes are sent when the system detects a primary or secondary phone line cut, or their respective restorals. When using single- digit reporting formats, only the second digit is sent.

27