Sierra S5832SG Block 8 SpreadNet Programming, Block 9 Partition Area Programming

Block 8 - SpreadNet Programming

The SpreadNet Programming Block has a total of 45 Command Locations (CL 001 - 045). The SpreadNet transmitters must be programmed with the SpreadNet Programmer. Refer to the Sierra Reference Manual for additional information.

SpreadNet Channel Comments

Cmd Loc

Default

Range

001

1

1 - 2

The Spread Spectrum channel used by the system.

SpreadNet Property Code

Cmd Loc 002 003 004 005

Default 0001

Range 0001 - 4048

Comments

Unique Property Code used to identify a transmitter as being part of the system. Program one digit per Cmd Loc.

SpreadNet Zone Transmitter Supervisory Rates (Zones 1 - 32)

Cmd Loc	006	007	008	009	010	011	012	013
Zone #	1	2	3	4	5	6	7	8
Cmd Loc	014	015	016	017	018	019	020	021
Zone #	9	10	11	12	13	14	15	16
Cmd Loc	022	023	024	025	026	027	028	029
Zone #	17	18	19	20	21	22	23	24
Cmd Loc	030	031	032	033	034	035	036	037
Zone #	25	26	27	28	29	30	31	32
Default	1 (All CL)
Range	1 - 4 (All CL)

Comments	Options:
The Supervisory Rate is the time interval	1	Unsupervised, Battery
between transmitter check-ins. A total of		status sent hourly
eight consecutive supervisory check-ins	2	30 seconds
must be missed before a supervisory fail-	3	120	seconds
ure is reported.	4	300	seconds

If option 1 is selected, unsupervised transmitters will send battery status hourly, only if they are within range of the receiver. Transmitters which are out of range will not be reported as missing, because they are unsu- pervised.

SpreadNet Keypad Supervisory Rate (Keypads 1 - 8)

Cmd Loc	038		039	040	041	042	043	044	045
Keypad #	1		2	3	4	5	6	7	8
Default	1	(All CL)
Range	1 -	4 (All CL)

Block 9 - Partition (Area) Programming

This Block has 178 Command Locations (CL 001 - 178) and is used to define all partition information, including which zones, user codes, and keypads are assigned to each partition. SpreadNet SN991-REMOTEs and SN961-KEYFOBs are associated with a specific user number and both sections must be programmed for them to function.

Partition Type

Cmd Loc 001

Default 1

Range 1 - 3

Comments

This option is used to specify whether or not a partitioned system has a common area and the type of display used in the common area.

Options:

1No Common Area

2Common Area - Full View Keypad

3Common Area - Limited View Keypad

Zone Assignments to Areas (Zones 1 - 32)									Comments
Cmd Loc	002	003	004	005	006	007	008	009	Each zone may be individually assigned to an
Zone #	1	2	3	4	5	6	7	8	Area (Partition) or disabled.
Cmd Loc	010	011	012	013	014	015	016	017
Zone #	9	10	11	12	13	14	15	16
Cmd Loc	018	019	020	021	022	023	024	025
Zone #	17	18	19	20	21	22	23	24
Cmd Loc	026	027	028	029	030	031	032	033
Zone #	25	26	27	28	29	30	31	32
Default	1 (All CL)
Range	0 - 8 (All CL)

Options:

0Zone Disabled

1 Area 1

2 Area 2

3 Area 3

4 Area 4

5 Area 5

6 Area 6

7 Area 7

8 Area 8

35