Wiring Knock-outs Top | Sierra S5832SG instruction

261 mm 10.25"

Wiring Knock-outs

Figure 3 (a)

Mounting the S5832S

Enclosure

		Housing Mounting Holes
		Housing Mounting Holes
80
3
. mm		266 mm
	15"	266 mm
		10.5"

Wiring Knock-outs

Top

Wiring Knock-outs

372 mm 14.65"

Wiring Knock-outs

Left side

Figure 3 (b)	80	mm
	3.

Mounting the S5832	15"

Enclosure

PCB Mounting

Hardware

(see page 1 for details)

Housing Mounting Holes

Wiring Knock-outs

Bottom

348 mm 13.7"

Housing

Mounting Holes

Wiring Knock-outs

Right side

Page 6

Image 6

Sierra S5832SG installation instructions Wiring Knock-outs Top

Contents

Installation Instructions Page Table of Contents Country Specific Compliance Information Sierra Accessory LoadingAH Requirements for Backup Singapore Mounting the Panel Panel Setup and InstallationIntroduction Earth Ground Wiring Knock-outs Top Sierra Accessory Loading Backup BatteryAH Requirements for Backup AC Power Sierra Accessory Wiring Distances Keypad WiringKeypad Wiring Output Terminals On-Board Relay Terminals TB2 AccessoriesZone Terminals S5050 Relay/Event Memory Module S5058 Zone Expansion Module SN961 SpreadNet Keyfob SN915-BUS SpreadNet ReceiverSN990/991 SpreadNet Keypad/Remote Digital Communicator Connections Programming the Panel Remote Programming RPSTerminal Connections Value Press Home to activate the RPS featureProgramming With an LED Keypad Zone LEDs Cmd Loc Data Value Programming With an Alpha Keypad Quick Programming ModeMenu Programming Mode Programming With an Icon Keypad Installer Mode Options, Block Installer Walk-TestEvent Memory Exit Delay Test Bypass 0 Home CancelEntry Delay Test Battery Test Block 1 Code Option Programming Block 2 Zone Configuration Programming Zone Response Time Zones 1 Chime Enable ZonesZone Bypass Enable Zones Audible Cadence Zones 1 Block 3 Armed System Programming 4X Exit Delay Extension Enable Comments Options Quick Bypass Enable CommentsHome Arm Exit Delay Enable Low Battery Arming Comments Options Auto-Disarming Enable Day of Week Auto-Arming Enable AreaAuto-Disarming Enable Area Comments Swinger Alarm Lockout Limit Comments Soak Mode Learning Period Duration Days Sounder Turn-On Delay Following Alarm Seconds CommentsStrobe/Siren Disable with Low Battery Comments Options Duress Active Only When Area Armed Sounder Bell Test Enable By Area Comments Keypad Tamper Switch Enable By Address Keypad #External Bell Reverse Enable Comments Options Home Arming Enable Comments Options Block 4 Digital Communicator Programming Account #5 Account #3Account #4 Account #6 Alarm Dialing Delay Seconds Comments RPS Callback Enable CommentsKeypad RPS Enable Comments Hour Zone Dial Delay Comments Options SpreadNet Transmitter Low Battery Report Routing Comments Power Supply Report RoutingInstaller Programming Report Routing Comments Keypad and Accessory Tamper Report Routing Comments Block 5 Reporting Digits Programming Report Code, Trouble Zones 1 Comments Report Code, Restoral Zones 1Report Code, Zone Bypass Zones 1 Comments Report Code, Tamper Zones 1 Report Code, AC Power Restoral Report Code, Cancel Users 1 User #Report Code, AC Power Loss Report Code, Low Battery Report Code, Ground Fault Report Code, Installer Programming StartReport Code, Installer Programming Complete Report Code, Ground Fault Restoral Report Code, Accessory Tamper Report Code, SpreadNet Keypad/Keyfob Low BatteryReport Code, SpreadNet Keypad/Keyfob Low Battery Restoral Report Code, Accessory Tamper Restoral Block 6 Real Time Clock Programming Block 7 Auxiliary Devices Programming Timer Count On Board Relay Exit Delay TerminatorTimer Units On Board Relay Timer Units Remm #1, Relay #1 Timer Units Remm #8, Relay #2 Timer Units Remm #2, Relay #1Timer Count Remm #2, Relay #1 Timer Count Remm #2, Relay #2 Timed Relay Closing Timer #1 Minutes Timed Relay Closing Timer #1 Day of WeekTimed Relay Closing Timer #1 Hours Timed Relay Closing Timer #2 Day of Week Block 8 SpreadNet Programming Block 9 Partition Area Programming Keypad Assignments to Areas Keypads 1 Area Access by User Number User # 1First to Open/Last to Close Enable Comments Options Area Assignments SpreadNet Keypads 1 Area Access SN Keyfob/Remote # 1 Block 10 User Code ProgrammingUser Codes User # 1 User Codes User Codes Comments