Manuals / IBM / Computer Equipment / Personal Computer

IBM 6824, 2289 manual Connecting the first IDE CD-ROM drive or DVD-ROM drive, User Guide

Models: 2289 6824

1 60

Download 60 pages 40.42 Kb

Page 30

Connecting the first IDE CD-ROM drive or DVD-ROM drive

6.Install the drive into the bay. Align the screw holes and install two screws to secure the drive.

7.Each integrated drive electronics (IDE) drive requires two cables; a four-wire power cable that connects to the power supply and a signal cable that connects to the system board. For a CD-ROM drive, you might also have an audio cable.

The steps to connect an IDE drive are different depending on the type of drive you are connecting. Use one of the following procedures for your drive connection.

Connecting the first IDE CD-ROM drive or DVD-ROM drive

1.Locate the three-connector signal cable that comes with your computer or with the new drive.

2.Locate the secondary IDE connector on the system board. See “Identifying parts on the system board” on page 11.

3.Connect one end of the signal cable to the drive and the other to the secondary IDE connector on the system board. To reduce electronic noise, use the connectors at the end of the cable only.

4.Your computer has extra power connectors for additional drives. Connect a power connector to the drive.

18User Guide

Image 30

IBM 6824, 2289 manual Connecting the first IDE CD-ROM drive or DVD-ROM drive, User Guide

Contents

User Guide Type 2289 and NetVistaPage User Guide Type 2289 and NetVistaSecond Edition October Appendix A. Updating System iv User Guide To avoid a shock hazard Safety InformationDANGER DANGERDanger of explosion if battery is incorrectly replaced Lithium battery noticeModem safety information Do notLaser compliance statement Consignes de sécurité relatives au modemDANGER viii User GuideOverview Information resourcesx User Guide Microprocessor Chapter 1. Installing optionsFeatures MemoryPower System management featuresInput/output features Video subsystemOperating systems preinstalled varies by model type Security featuresIBM preinstalled software Operating systems tested for compatibility1Specifications This section lists the physical specifications for your computerAvailable options Tools requiredHandling static-sensitive devices Installing external options 6 User GuideLocating the connectors on the front of your computer 1and 2USB connectorsLocating the connectors on the rear of your computer 8 User GuideObtaining device drivers ConnectorDescription Removing the cover 6Power supply Locating componentsIdentifying parts on the system board 1Microprocessor and heat sinkInstalling memory What to do next Installing adapters 14 User GuideInstalling internal drives What to do nextDrive specifications Installing a drive Connecting the first IDE CD-ROM drive or DVD-ROM drive 18 User GuidePhysical security Connecting an additional IDE CD-ROM drive or DVD-ROM driveConnecting an additional IDE hard disk drive What to do nextChanging the battery What to do next1 Padlock loop 2 Integrated cable lock 3 Rope clip Replacing the cover and connecting the cables Erasing a lost or forgotten password clearing CMOS 22 User Guide9. Repeat steps 2 through 4 on page 24 User Guide Viewing and changing settings Chapter 2. Using the IBM Setup Utility programStarting the IBM Setup Utility program Exiting from the IBM Setup Utility programSetting, changing, and deleting a password User passwordAdministrator password Using Security Profile by DeviceChanging the startup device sequence Selecting a startup deviceSelecting a temporary startup device Chapter 2. Using the IBM Setup Utility program28 User Guide Appendix A. Updating System Programs Updating flashing BIOS from a disketteUpdating flashing BIOS from your operating system System programsRecovering from a POST/BIOS update failure Appendix B. Manual modem commands Basic AT commandsATH ENTER Extended AT commands 32 User GuideAppendix B. Manual modem commands Fax Class 2 commands MNP/V.42/V.42bis/V.44 commandsFax Class 1 commands 34 User GuideVoice commands #VBQ? #VBS #VBT #VCI? #VLS #VRA #VRN #VRX #VSDB #VSK #VSP #VSR #VSS #VTD #VTM #VTS #VTXAppendix C. System address maps System memory mapI/O address map Description Address range hexSize bytes 38 User GuideDMA I/O address map Appendix C. System address mapsBits Address hexDescription Byte pointerNote The default settings for COM 1 IRQ 4, COM 2 IRQ 3, and LPT 1 IRQ The following tables list the IRQ and DMA channel assignmentscan be changed to another IRQ 42 User Guide IBM Director of Licensing IBM Corporation North Castle Drive Appendix E. NoticesTelevision output notice Armonk, NY U.S.ATrademarks 44 User GuideIndex A Page Page Part Number 49P1040 Printed in U.S.A 1P P/N 49P1040