Manuals / IBM Partner Pavilion / Computer Equipment / Switch

IBM Partner Pavilion T400F manual Setting the Scsi ID with a Scsi ID Switch

Models: T400 T400F

1 136

Download 136 pages 10.3 Kb

Page 30

Figure 5. SCSI ID settings on the SCSI ID connector

Setting the SCSI ID with a SCSI ID Switch

If your enclosure uses a SCSI ID switch (rather than jumpers), connect the switch

to the drive’s SCSI ID connector (see in Figure 2 on page 14). If any jumpers are pre-installed, be sure to remove them before connecting the switch. The SCSI ID switch must be compatible with the drive’s SCSI ID connector and must make an electrical connection between the same pins as the jumpers to achieve the same corresponding SCSI ID.

Setting the SCSI ID Through the LDI Interface

If you are installing the Ultrium 2 Tape Drive into a tape library, you can issue a command from the library to set the drive’s SCSI ID through the LDI interface. Make sure that the SCSI ID is set to 15 (see Figure 5). When configured to accept its SCSI ID through the LDI interface, the drive does not respond to SCSI commands until it receives a Set Configuration command through the interface.

Supplying TERMPOWER (SCSI Drive Only)

To supply TERMPOWER to the bus, locate one of the five jumpers shipped with the Ultrium 2 Tape Drive and place it on the SCSI ID connector as shown in the following figure. Place the jumper on the pins that are shaded.

A67E0049

Note that you must provide SCSI termination externally to the Ultrium 2 Tape Drive.

18IBM TotalStorage LTO Ultrium 2 Tape Drive

Image 30

IBM Partner Pavilion T400F manual Setting the Scsi ID with a Scsi ID Switch, Setting the Scsi ID Through the LDI Interface

Contents

Setup, Operator, and Service Guide Page Setup, Operator, and Service Guide First Edition November Contents Operating the Tape Drive Contents Vi IBM TotalStorage LTO Ultrium 2 Tape Drive Safety and Environmental Notices ViiLaser Safety and Compliance Sample caution notices followPreface IBM TotalStorage LTO Ultrium 2 Tape Drive Introduction Sleep Mode Cartridge CompatibilitySpeed Matching and Channel Calibration Supported Servers and Operating Systems Supported Servers Supported Operating SystemsSupported SAN Components for Fibre Channel Attachment Physical Characteristics of the Scsi Interface Scsi AttachmentSpeed Address Assignments Fibre Channel Attachment Supported TopologiesType of Fibre Channel Connection to Server Speed Physical Characteristics of the Fibre Channel Interface World Wide NamesSupported Device Drivers IBM TotalStorage LTO Ultrium 2 Tape Drive Power Specifications SpecificationsSpecification Measurement Physical Specifications Other Specifications for both interface types26C Installing the Tape Drive Rear View of the Scsi Drive Rear View of the Fibre Channel Drive Remove Power from the Enclosure Unpack the DriveSetting the Scsi ID Scsi Drive Only Setting the Scsi ID with JumpersSet the Scsi ID or Arbitrated Loop Physical Address Setting the Scsi ID with a Scsi ID Switch Setting the Scsi ID Through the LDI InterfaceSupplying Termpower Scsi Drive Only Installing Setting the Loop ID to Provide Status About the Loop LID Setting the Loop ID to Provide Additional Loop IDs Alpa LID Change the Link Services of the Drive optional Fibre Channel Pin Characteristic Through Speed SelectionFibre Channel Pin Characteristic Through Mount the Tape Drive into the Enclosure Connect and Test Power to the Tape Drive Connect the Internal Scsi or Fibre Channel CableConnect the Internal LDI Cable optional Run Drive DiagnosticsInstall the Device Drivers Connect the External Scsi Interface to the ServerConfigure the Tape Drive to the Server, Switch, or Hub Connect the External Fibre Channel Interface to the ServerConnect the External LDI Interface to the Server optional IBM TotalStorage LTO Ultrium 2 Tape Drive Operating the Tape Drive Front view of the IBM TotalStorage LTO Ultrium 2 Tape DriveStatus Light Color and Condition Meaning Status LightUnload Button Single-Character DisplaySingle Red Dot Inserting a Tape Cartridge Inserting a cartridge into the Ultrium 2 Tape DriveCleaning the Drive Head Removing a Tape CartridgeSelecting a Diagnostic or Maintenance Function Function Code 2 Update Tape Drive Firmware from FMR Tape Function Code 3 Create FMR TapeFunction Code 4 Force a Drive Dump Function Code 6 Run Scsi or Fibre Channel Wrap Test Running a Scsi Wrap TestTesting the Circuitry at the Fiber Cable Running a Fibre Channel Wrap TestFunction Code 7 Run LDI or RS-422 Wrap Test Function Code 8 Convert FMR Tape to Scratch TapeFunction Code 9 Display Error Code Log Function Code a Clear Error Code LogFunction Code C Insert Cartridge into Tape Drive Function Code E Test Cartridge & Media Function Code F Fast Read/Write TestFunction Code P or U Enable or Disable Post Error Reporting Function Code H Test HeadFunction Code L Reserved for Future Use Exiting Maintenance Mode Updating the FirmwareUpdating Firmware through the Library/Drive Interface Updating the Firmware with an FMR Tape Cartridge Using the Media IBM TotalStorage LTO Ultrium 200 GB Data CartridgeData Cartridge Cleaning Cartridges Setting the Write-Protect Switch Handling the CartridgesProvide Training Ensure Proper PackagingProvide Proper Acclimation and Environmental Conditions Perform a Thorough InspectionHandle the Cartridge Carefully Checking for gaps in the seams of a cartridgeExamples of Cartridge Problems Example Improper Placement of Leader PinRepositioning or Reattaching a Leader Pin Repositioning a Leader PinRemove the rewind tool by pulling it away from the cartridge Reattaching a Leader Pin Cartridge manual rewind tool seeIBM TotalStorage LTO Ultrium 2 Tape Drive A67E0036 On the leader pin Using the Media Temperature 10 to 45C 16 to 32C 16 to 25C −23 to 49C Disposing of Tape Cartridges Ordering Media SuppliesIBM Part Number Product Description Ordering Custom Bar Code Labels America Europe and AsiaResolving Problems If the problem is this Do thisMethods of Receiving Errors and Messages If the error or message was Do this Presented byDescriptions and Corrective Actions for Errors and Messages Code Cause and ActionCode Cause and Action For Problems with Writing Data For Problems with Reading DataFor Scsi drive For Fibre Channel driveUsing Sense Data Obtaining Error Information from the RS/6000 or pSeries Press F4 to view the sense data see the example in FigureExample of a Drive Error Log Example of a Scsi Bus Error Using the Drive to Obtain a Dump Using a Device Driver Utility to Obtain a DumpObtaining a Drive Dump Viewing the Drive Error Log Resolving Problems Reported by the Server Fixing Scsi Bus ErrorsFixing a Consistent Error with a Single Drive on a Scsi Bus IBM TotalStorage LTO Ultrium 2 Tape Drive Fixing Fibre Channel Errors Starting Problem DeterminationFixing a Consistent Error in a Point-to-Point Topology Fixing Intermittent Fibre Channel Errors Resolving Media-Related Problems Servicing the Tape Drive Removing a Scsi Tape Drive from an EnclosureRemoving a Fibre Channel Tape Drive from an Enclosure Manually Removing a Tape Cartridge Removing the CartridgeDetermining whether the tape is broken Servicing Fixing an Internal Jam Removing the top cover of the drive Rewinding the leader pin into the tape cartridge Guiding the leader block into the home position IBM TotalStorage LTO Ultrium 2 Tape Drive Servicing Rotating the loader motor gear until the cartridge ejects Appendix A. Tools and Supplies IBM Part Number Product DescriptionIBM TotalStorage LTO Ultrium 2 Tape Drive Appendix B. TapeAlert Flags TapeAlert Flags Supported by the DriveFlag Description Action Required Number Hex 0Ch 22h IBM TotalStorage LTO Ultrium 2 Tape Drive Trademarks IBMFederal Communications Commission FCC Class B Statement Industry Canada Class B Emission Compliance StatementAvis de conformité à la réglementation d’Industrie Canada European Union EU Electromagnetic Compatibility Directive Germany Electromagnetic Compatibility DirectiveJapan Vcci Class B ITE Electronic Emission Statement Warranty Getting HelpNumbers and Symbols GlossarySee Celsius Data compression. See compressionFibre Channel configuration/status connector Fibre Channel-Arbitrated Loop FC-AL topology. aFMR tape. See field microcode replacement tape LAN. See local area network LDI. See Library/Drive Interface Log sense data. See Scsi log sense data Media capacity. See capacityNative sustained data transfer rate. See data Transfer rateSee second SAN. See Storage Area Network Glossary TotalStorage LTO Ultrium 2 Tape Drive. See IBM Ultrium 2 Tape Drive. See IBM TotalStorage LTOWAN. See wide area network IBM TotalStorage LTO Ultrium 2 Tape Drive Index AIX AlpaLID Cables Connecting to a bus Fixing errors Sleep mode Wrap test, running Fibre Channel LDI or RS-422 IBM TotalStorage LTO Ultrium 2 Tape Drive Page GA32-0455-00