Insignia NS-AV511 Listening to the radio, Presetting FM or AM stations, Listening to your receiver, TUNER, TUNER, TUNER, D.TUN, TUNING, PHONES, TUNING, MEMORY, PRESET, MEMORY

Insignia NS-AV511 Surround Sound Receiver

	The SLEEP indicator lights on the display when
			Tip
	the sleep timer has been set. The specified sleep
				You can also press the TUNE MODE and arrow
	time appears on the display for about five
				buttons on the remote control.
	seconds, then the previous display reappears.
			- OR -
	Tip
			• To manually tune to a station:
		• To cancel the sleep timer, press SLEEP
		repeatedly until the SLEEP indicator goes off.		• Press TUNING MODE until the AUTO
		• To check the time remaining until the receiver		indicator goes off.
		turns off, press SLEEP. If you press SLEEP while
				• Press and hold TUNING or . The
		the sleep time is being displayed, the sleep time
		is shortened by 10 minutes.		receiver tunes up or down the frequency
				band as long as you hold the button. Press
Using headphones
				the button repeatedly to tune up or down

To use headphones:

by steps.

•Connect a pair of stereo headphones with a standard plug (1/4 in. or 6.3 mm) to the PHONES jack.

Tip

•Always turn down the volume before connecting your headphones.

•While the headphones plug is inserted in the PHONES jack, the speakers are turned off.

•When you connect a pair of headphones, the listening mode is set to Stereo, unless it is already set to Stereo, Mono, or Direct.

•The listening modes cannot be selected while a pair of headphones is connected.

Listening to your receiver

Important

The procedures described in this section use the buttons on the front panel, unless otherwise specified.

Listening to the radio

With the built-in tuner you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection.

To listen to the radio:

•Press TUNER to select either AM or FM (each time you press TUNER, the radio band changes between AM and FM).

In this example, FM has been selected.

BandFrequency

•To automatically tune to a station:

•Press TUNING MODE until the AUTO indicator appears on the display.

•Press TUNING or . The receiver automatically searches for stations and stops when a station is found.

FM Stereo

AUTO

TUNED

Tip

•In Manual Tuning mode, FM stations are in mono.

•If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono.

•You can also press the TUN MODE and arrow buttons on the remote control.

-OR -

•To tune to a station by entering the frequency:

•Using the remote control, press TUNER repeatedly to select AM or FM, then press D.TUN.

•Within eight seconds, press the number buttons to enter the frequency of the radio station you want. For example, to tune to 87.50, press 8, 7, then 5.

Presetting FM or AM stations

You can store a combination of as many as 40 of your favorite AM or FM stations as presets.

To store a station as a preset:

1Tune to the FM or AM station that you want to store as a preset. See “Listening to the radio” on page 17 for information on tuning your receiver.

2Press MEMORY. The preset number flashes.

3While the preset number is flashing (about eight seconds), press PRESET or to select a preset number from one through 40.

4Press MEMORY again to store the station or channel. The station or channel is stored and the preset number stops flashing.

5Repeat steps 1 through 4 to preset your favorite radio stations.

Tuning to a preset station

To tune to a preset station:

•To select a preset, press PRESET or on the receiver, or press CH +/– on the remote control.

Tip

You can also press the number buttons on the remote control to select a preset station directly.

www.insigniaproducts.com 17