Insignia NS-AV511 Changing audio settings, OFF, Off, HDMI, THRU, HDMI, Auto, HOME, HOME, Bass, 0 dB, 0 dB, 10 dB, 10 dB, +10 dB, Treble, +10 dB, Standby, RECEIVER, Audio TV Out

Insignia NS-AV511 Surround Sound Receiver

When enabling the HDMI Through function,	• To disable, set to OFF.
regardless of whether the AV receiver is On or in
Standby, both the audio and video streams from an		Notes
HDMI input will be output to the TV or other			• This function only works if your
HDMI input will be output to the TV or other			HDMI-compatible TV supports HDMI Lip Sync.
components via the HDMI connection. The HDMI			HDMI-compatible TV supports HDMI Lip Sync.
components via the HDMI connection. The HDMI			• You can check the amount of delay being
THRU and HDMI indicators light when this is			• You can check the amount of delay being
THRU and HDMI indicators light when this is			applied by the HDMI Lip Sync function on the
enabled. This setting is set to Auto automatically			A/V Sync screen.
when the above CEC Function is set to On.
when the above CEC Function is set to On.

Notes

•Only the input source assigned to the HDMI IN via “HDMI Input” is enabled.

•The power consumption during standby mode will increase when the HDMI Through function is turned on, however, in the following cases, the power consumption does not increase:

•The TV is in standby mode.

•You are watching a TV program.

•Refer to the connected component’s instruction manual for details.

•Depending on the connected component, the correct input source may not be selected with the setting set to Auto.

•This setting is set to Off automatically when CEC Function is set to Off.

Audio TV OUT (Audio TV Out submenu)

This setting determines whether audio received by HDMI IN is output by the HDMI OUT. You may want to turn this preference on if your TV is connected to the HDMI OUT and you want to listen to the audio from a component that’s connected to an HDMI IN, through your TV’s speakers. Normally, this should be set to Off.

Notes

•If On is selected and the signal can be output by the TV, the receiver outputs no sound through its speakers.

•If On is selected, TV Sp On appears on the display when you press DISPLAY.

•When TV Control is set to On, this setting default is Auto.

•With some TVs and input signals, no sound may be output, even when this setting is On.

•When the Audio TV OUT or TV Control are set to On, and you are listening through your TV’s speakers, if you turn up the receiver’s volume control, the sound is output by the receiver’s front left and right speakers. To stop the receiver’s speakers from producing sound, change the settings, change your TV’s settings, or turn down the receiver’s volume.

Audio Return Ch (ARC)(Audio Return Ch submenu)

The audio return channel (ARC) function enables an HDMI 1.4-capable TV to send the audio stream to the HDMI OUT jack of the receiver. To use this function, you must select the TV/CD input and your TV must support the ARC function.

Notes

•The Audio Return Ch setting can only be set when HDMI Control is On.

•This setting is set to Auto automatically when HDMI Control is set to On first time.

Changing audio settings

You can change various audio settings by pressing HOME on the remote control.

Note

When Audio TV OUT is set to On, the HOME button is disabled.

To change audio settings:

1Press RECEIVER on the remote control, then press HOME.

2Press or to select an option, then press

or to change the setting. Repeat this step to change additional settings.

Changing tone control settings

You can adjust the bass and treble for the front speakers, except when the Direct Listening mode is selected. Options include:

•Bass–You can boost or cut low-frequency sounds output by the front speakers. 10 dB to 0 dB to +10 dB, in 2 dB steps

•Treble–You can boost or cut high-frequency sounds output by the front speakers. 10 dB to 0 dB to +10 dB, in 2 dB steps

Notes

•To bypass the bass and treble tone circuits, select the Direct listening mode.

•This procedure can also be performed on the receiver by pressing the TONE–/+buttons.

Changing the speaker levels

You can adjust the volume of each speaker while listening to an input source. These temporary adjustments are cancelled when the receiver is set to Standby. To save the setting you made here, go to “Setting the level calibration (Level Cal menu)” on page 15, before returning the receiver to Standby. Options include:

•Subwoofer–15 dB to 0 dB to +12 dB, in 1 dB steps.

•Center–12 dB to 0 dB to +12 dB, in 1 dB steps.

Notes

•You cannot use this function while the receiver is muted.

•Speakers that are set to No or None in the Sp Config (Speaker Configuration) submenu cannot be adjusted.

LipSync (LipSync submenu)

Lets you set the receiver to automatically correct any delay between the video and the audio, based on the data from the connected monitor.

• To enable, set to ON.