Integra DTR-7 Enjoying Music and Movies in the Sub-room, To control the system in the sub-room

Enjoying Music and Movies in the Sub-room

MULTI SOURCE indicator

SMART SCAN Controller

FM MUTE/

CHARACTER/

SP/SYS

AUDIO

BASS/

MASTER VOLUME

DIMMER

MODE

DOWN

TUNING

UP

MEMORY

SETUP

ADJUSTMENT

TREBLE

STANDBY/ON

MODE

W

N

D O

U

PRESET/MODE ADJ

P

STANDBY MULTI SOURCE

MULTI SOURCE

POWER

ON OFF

PUSH TO ENTER

A SPEAKERS B

LISTENING MODE

REC OUT/ DIGITAL/

DISPLAY

DIRECT

STEREO

/DTS

THX

DSP MULTI SOURCE ANALOG

CH LEVEL

SURROUND

MODE

PHONES

MULTI CH INPUT

VIDEO4 (MONO)

DVD

VIDEO-1

VIDEO-2

VIDEO-3

VIDEO-4

TAPE

FM

AM

PHONO

C D

S VIDEO

VIDEO L AUDIO R

DTR-7 by

REC OUT/MULTI SOURCE

1. POWER ON

2. Input Selector

To control the system in the sub-room

1.Press the POWER ON button on the remote controller. The MULTI SOURCE indicator located below the STNDBY/ ON button on the receiver will light to indicate that the system enters the Multi-Source mode.

Note:

If you operate the system in the sub-room while a recording is going on in the main-room, the source of the recording switches to the source which you are playing in the main room. Be careful when you are recording a different source from the one that you are playing.

2.Press the appropiate Input Selector button on the remote controller to select your desired source and start operating it.

3.Adjust the volume on the power amplifier to the desired level.

To control the system using the main unit (e.g. when no remote controller is available):

1.Press the REC OUT/MULTI SOURCE button on the system to make sure the MULTI SOURCE indicator flashes in the display window.

2.Making sure that the indicator flashes, select a source by us- ing the Smart Scan Controller.

Adjust the volume in the sub-room.

Notes:

•In the sub-room, you can only play the source in the 2-Channel mode. You cannot play the source in the Multi-Channel mode or the Surround mode.

•If you press the REC OUT/MULTI SOURCE button in the main room while you are playing the source in the Multi Source mode in the sub- room, the Multi Source function will be deactivated and the source will be inaudible in the sub-room.

•Please note that some third-party multi-room system components may not be fully compatible with the Onkyo multi-room system components.

When the system is mounted in a rack:

DTR-7/DTR-6

DIGITAL INPUT	R	L	R	L	V	S	SURROUND SPEAKERS	FRONT SPEAKERS A
	AMP IN

	FRONT					OUT
COAXIAL					VIDEO-1	ANTENNA
1	PRE OUT						R	L	R	L
	FRONT					IN
COAXIAL
2	SUB
	WOOFER					OUT			CENTER
OPTICAL
1	CENTER				VIDEO-2				SPEAKER
						IN			CAUTION: SPEAKER IMPEDANCE
OPTICAL	SURROUND						R	L	6 OHMS MIN. / SPEAKER
2
	FRONT				VIDEO-3
						IN
OPTICAL
	SUB				DVD		FRONT SPEAKERS B		AC OUTLETS
	WOOFER								AC 120V 60Hz
DIGITAL OUTPUT						IN			SWITCHED
	CENTER					AV RECEIVER			TOTAL 120W 1A MAX.
	SURROUND			(REC)	MONITOR	MODEL NO. DTR-7
	MULTI CHANNEL
	INPUT			OUT	OUT
	R		L	TAPE	�					AC INLET
	CD			IN
				(PLAY)
	GND				VIDEO
	PHONO				S VIDEO
	R	L	R	L	OSD SELECTOR
						LOCAL REMOTE	REMOTE
							CONTROL
						1
							HB-100			Power
										supply
LOCAL		REMOTE					Connecting block

Mini Plug cable 120V AC

(unswitched)

In the rack

To enable remote operation when the receiver is mounted in a rack which will not permit infrared beams to pass, install the remote sen- sor at a location outside of the rack where the infrared beams from the controller can reach.

1.Connect the LOCAL jack (on the rear of the receiver) to the connecting block.

2.Install the remote sensor at a location where it can detect the infrared beams from the remote controller. Then, connect the remote sensor to the connecting block.

2

Remote sensor HR-600 Remote contoroller

Outside of the rack

47