Using the remote controller, Send/Learn, Indicator | Integra DTR-7

Using the remote controller

Using the remote controller

Overview

When you use a remote controller, typically you press one of the MODE buttons that corresponds to the device you wish to control, then press the operation buttons. For example, if you wish to control the receiver from a remote controller, first press the MODE AUDIO button, then press an appropriate operation button. To control a CD player, press the MODE CD button, then press an appropriate operation button.

First, press the desired MODE button to make sure that the receiver is set to a correct mode.

Using the RC-392M to control each device

SEND/LEARN
indicator
POWER ON	POWER
	STNBY

MODE AUDIO

Turning the power on and off to the receiver

Note:

Before operating the RC-392M, turn on the POWER switch on the the receiver so that the unit enters standby mode.

1.Press the MODE AUDIO button.

2.Press the POWER ON button.

Pressing the POWER STNBY button will activate the power standby mode.

SEND/LEARN indicator

This indicator acts as a guide when commands are programmed into or sent by the remote controller. It also warns the user when an error is made or battery power is low.

POWER ON/STNBY

SLEEP LIGHT

MODE

AUDIO

DISPLAY
CH +/–	VOL
	TEST
	MUTING

INPUT

SELECTOR

Listening mode

SP A/B	LEVEL +/–
DIMMER	CH SEL

Controlling the receiver

1.Press the MODE AUDIO button.

2.Press the desired operation button.

Shaded buttons in the figure are the operation buttons used to control the receiver.

SLEEP : Sleep function

POWER ON/STNBY

:Power on/standby

DISPLAY : Changing the display

VOL Δ/∇ : Adjusting the volume

CH +/- : Tuner preset number increment/decrement

INPUT SELECTOR Listening mode

:Changing Listening mode

SP A/SP B	: Switching between Speakers A and B
CH SEL	: Selecting a speaker
DIMMER	: Adjusting the brightness of the display
LEVEL +/-	: Adjusting the speaker levels
TEST	: Test tone
MUTING	: Muting
LIGHT	: Illuminating the buttons.

49

Image 49

Integra DTR-7 Using the remote controller, Using the RC-392Mto control each device, Controlling the receiver, Send/Learn

Contents

Preparation Before usingOperation Appendix AVIS Important Safeguards 1. Warranty Claim Precautions5.Power Note to CATV system installer Supplied accessories FeaturesKey Features Aluminum volume control Installing the remote controller batteries Before operating this unitUsing the remote controller Do not plug in the power Audio equipment connectionscord until all connections have been made Connections for remote control z Audio equipment connectionsAC outlet connection Video equipment connections Connecting equipment with 5.1-channeloutput Video equipment connectionsDecoder with 5.1-channeloutput Speaker placement Connecting speakers FRONT SPEAKERS Connecting speakersSURROUND SPEAKERS CENTER SPEAKER Connecting speakers Connecting power amplifiersConnecting a subwoofer Connecting power amplifiers Connecting the power Connecting an equalizer DTR-7Connecting a power cable Connecting the power Connecting the antenna cable Making antenna connectionsDirectional Iinkage Assembling the AM loop antenna Connecting the included antennas Making antenna connectionsConnecting an FM outdoor antenna Connecting an AM outdoor antenna How to use the on-screendisplay Using the on-screendisplayScreen Setup OSD screens Using the on-screendisplay Front Setting the speaker configurationCenter Surround Setting the speaker configuration parameters Using the on-screendisplay Setting the speaker configuration Using the on-screendisplay Setting the speaker distanceLoudspeaker Position Time Synchronization Center Setting the speaker LevelRight R-Sur Setting the bass peak level Setting the Speaker levelBass Peak Level Manager* DTR-7only Setting the Speaker level Playing a digital source Digital Input SetupUsing the on-screendisplay Digital input setup Tuning in a radio station Presetting FM/AM radio stations Cancelling preset stations Presetting FM/AM radio stationsProgramming radio stations 3. Start playing the selected input source Selecting an input source Selecting an input source Selecting an input source Using the on-screendisplay Digital Input SetupSelecting an input source COAXIAL Selecting the speaker system Selecting an input sourceChanging the display Selecting an input source Adjusting the tone Bass and treble adjustment Using the on-screendisplay Selecting a preset station Setting the MULTI CHANNEL INPUT Playing a multichannel input sourceUsing the on-screendisplay Before Using Listening Mode Using the Listening ModesDSP Digital Signal Processor Listening Modes 3. MASTER VOLUME control knob Using the listening modes3. VOLUME buttons 2. Listening mode button Using the listening modes Using the listening modes Input sources and listening modes Using the listening modes How to set the listening mode parameters Setting the listening mode parametersUsing the on-screendisplay Listening mode parameters Setting the listening mode parametersRe-EQCinema Re-Equalization Late Night Video Assign Setup Video Assign SetupUsing the on-screendisplay PHONO Giving a name to each input source Giving a name to each preset radio stationTo change a name To erase a name To use the above setting from now on Fine-tuningthe output level of each speaker1.Press the CH LEVEL button 3.Repeat the operation described in step Volume display method setup Other setup operationsIntelliVolume setup Using the on-screendisplay movie Recording a source while listening to music or aRecording from on audio /video source Recording a source Using the on-screendisplay Recording a sourceAdding sound to a video tape Outline of Multi-roomRemote System Using Multi-RoomRemote SystemEnjoying Music and Movies in the Sub-room When the system is mounted in a rack Enjoying Music and Movies in the Sub-roomTo control the system in the sub-room Initial settings The initial settingsConfig Setup Distance Setup Using the RC-392Mto control each device Using the remote controllerTurning the power on and off to the receiver indicator Controlling an Onkyo/Integra CD player Using the remote controllerControlling an Onkyo/Integra DVD player Controlling an Onkyo/Integra MD recorder Using the remote controllerControlling an Onkyo/Integra tape deck MODE SAT, CABLE, VCR, and TV buttons Programming procedure Erasing a learned code from a MODE button Erasing a learned code 2 1 Using a Macro functionWhat is a Macro function? Programming Macro mode Macro Direct Learning function Using a Macro function Using a Macro function 1.Open the battery cover and remove the batteries Using a Macro function3.Press the ENT button Trouble Troubleshooting guideCause Remedy FM/AM Troubleshooting guideVideo & audio Others DTR-7 SpecificationsDTR-6 REMOTE CONTROL SpecificationsREMOTE CONTROL DTR-7 Front panel Control positions and namesDisplay Remote controller Control positions and names1 2 3 4 5 6 7 8 9 22 21 20 19 Williams Drive, Ramesy, N.J. 07446, U.S.A ONKYO U.S.A. CORPORATIOND9907-1