Integra DTR-7 instruction manual Programming procedure

Programming the remote controller codes of other devices into the RC-392M

The RC-392M has two learning functions. One is a normal learning function that enables the RC-392M to learn other remote controllers’ codes. The other is a macro learning function, which enables the RC-392M to learn a series of codes already memorized in the remote controller into one MACRO button.

Programming procedure

Any button is programmable except for the eight Mode buttons (AUDIO, CD, DVD, MD, SAT, CABLE, VCR, and TV), two Macro buttons (DIRECT and MODE), and LIGHT button.

2 Light

CH- INPUT

MULTI

1

4
									385S-
									RC
							VOLUME
									MUTING
							TESTTONE		LEVEL
								SEL	CH
		PRESET
D	C			DVD					TAPE
		PHONO	TUNER
				GROUP
SURMODE		SELECTORTUNER						DISC
				2-	VIDEO		DC
		DIMMER	INPUT	TAPE		-
						1	VIDEO
			SLEEP		DVD

POWER

RCONTROLLE REMOTE

3

5 to 15 cm

(2 to 6 inches)

RC-392M

1.Place the RC-392M and the remote controller for another device, with 5–15cm (2–6 inches) apart and the light-emit- ting parts facing each other.

2.While pressing and holding down the desired MODE button on the RC-392M (AUDIO, CD, DVD, MD, SAT, CABLE, VCR, or TV), press the ENT button, then release the but- tons.

When you press and hold down one of the MODE button, the SEND/LEARN indicator lights up. When you press the ENT button, the indicator turns off. When you release the buttons, the SEND/LEARN indicator lights up again.

3.Press and release the desired operation button on the RC- 392M.

You may select any button within the rectangle shown in the figure. When you press the button, the SEND/LEARN indicator turns off. When you release the button, the indicator lights up again.

4.Press and hold down the desired button on the remote con- troller of the other device until the SEND/LEARN indicator on the RC-392M flashes twice.

The SEND/LEARN indicator flashes twice slowly, then lights up.

5.Repeat Steps 3 and 4 to program other buttons in the same MODE.

Repeat Steps 2-4 to program other buttons in a different MODE.

6.Press the MODE button to complete programming.

7.Operate the programmed button to make sure the learning function works.

Note:

The remote controller codes for the Onkyo/Integra CD player, tape deck, DVD player, and MD recorder have already been programmed into the buttons on the RC-392M. You may pro- gram other remote controller codes into these buttons. If you wish to restore the Onkyo/Integra preset codes after you pro- gram new codes, erase the new codes. (See page 53.)

52

Notes:

•The remote controller can have max 408 memory slots (51 buttons by 8 modes), although this number varies significantly depending on the manufacturers and types of the remote controller you wish to program into the RC-392M. It is recommended that you determine which button functions have priority for programming.

•If you do not press any button for more than 30 seconds during the pro- cedure, the SEND/LEARN indicator flashes three times quickly, then the RC-392M exits Learning mode. Resume from Step 2.

•If you make a mistake during programming, the SEND/LEARN indica- tor flashes three times quickly, then the RC-392M exits Learning mode.

•If you try to program beyond the learning capacity of the RC-392M, the SEND/LEARN indicator flashes six times quickly, then the RC-392M exits Learning function. Try programming in a button of other MODE.

•Follow the same procedure when you wish to program new codes into the already-programmed buttons.

•This remote controller uses infrared rays. Most remote controller codes can be memorized using the infrared system; however, depending on the degree to which the system differs, there may be some rare occa- sions when memorization is not possible.

•Some remote controllers use a single button to perform different func- tions, with the function code changing each time the button is pressed. If you are using this kind of controller, please perform the “learn” opera- tions for each function individually to store each function to a button on the RC-392M.

•For instructions regarding the operation of “learned” units, please refer to the instruction manual for each product.

•Even after codes have been memorized, please keep your old remote controller in a safe place. If the memorized codes are lost when the bat- teries run down, it will be necessary to memorize them once again using the old remote controller.

•Make sure both the RC-392M and the product’s own remote controller have fresh batteries. If either of them has batteries that are wearing down, it may be impossible to store the remote controller codes into the RC-392M or the product may not respond properly to the buttons on the RC-392M for which the remote controller codes were stored into memory.