Intel 537EX manual Intel Confidential, IS-101Voice Mode AT Commands, Default, Description

IS-101 Voice Mode AT Commands

Table 25. Voice Mode Command Descriptions (Continued)

Command	Default		Description
		DTMF and Tone Generation: (cont.)
		3. Single DTMF tones or hook flashes are sent enclosed in braces “{ }”. A duration must be included,
		as the duration set in +VTD=m does not apply.
		Use the following format:
		AT+VTS={<DTMF or !>,<duration>}
		For example: AT+VTS={2,30}
		This command sends DTMF tone 2 with a duration of 300 ms.
		For example: AT+VTS={!,50}
		This command sends a hook flash with a duration of 500 ms.
		Send multiple DTMF signals and tones by combining elements in a given +VTS=m command
		string.
		For example:
		AT+VTS={!,30}, 1, 2, [1000,1300,50], !, {*,6}, [1000], 9
+VTS=m	none	This command line programs the following events:
(cont.)		1. Hook-flash with a duration of 300 ms.
		2.	Send DTMF 1 for the duration specified by +VTD command.
		3.	Send DTMF 2 for the duration specified by +VTD command.
		4.	Send tone pair 1000 Hz and 1300 Hz for a duration of 500 ms.
		5.	Hook-flash with a duration specified by +VTD command.
		6.	Send DTMF * for a duration of 60 ms.
		7.	Send tone 1000 Hz for a duration specified by the +VTD command.
		8.	Send DTMF 9 for the duration specified by +VTD command.
		For example:
		AT+VTS=1, [, ,50], 2, [ ], 9
		This command line programs the following events:
		1.	Send DTMF 1 for the duration specified by +VTD command.
		2.	Play silence for a duration of 500 ms.
		3.	Send DTMF 2 for the duration specified by +VTD command.
		4.	Play silence for a duration specified by +VTD command.
		5.	Send DTMF 9 for the duration specified by +VTD command.
		Play Mode: This command causes the modem to start voice transmission (playback mode) and play
		back a previously recorded voice message.
		Upon receiving the AT+VTX command, the modem responds to the DTE with a ‘CONNECT’ message
		at the current DTE-to-modem rate. It is important that the UARTs DTE-to-modem rate be equal to or
		higher than the compression-scheme-required UART data rate (for example, CL1 at 4800 samples/
		second requires 57,600 bps). If the DTE-to-modem data rate is lower than the compression-scheme-
		required UART data rate, then data may be lost or the playback message may be garbled. After
		receiving the ‘CONNECT’ message, the DTE then sends the voice file to the modem. To ensure that
		data is not overwritten, the modem provides both hardware or software flow control with AT+FLO=m.
		The modem also buffers the data to ensure steady voice delivery, even though the voice data may be
		transferred from the DTE in bursts.
+VTX	none	Playing mode is terminated when the data is exhausted and the modem receives the two terminating
		characters <DLE><ETX> from the DTE. Upon detecting <DLE><ETX>, the modem issues an ‘OK’ result
		code. After the modem’s internal buffer is empty, it returns to the command mode.
		To abort playback mode immediately without waiting for the modem to empty its internal buffer, send
		<DLE><CAN><DLE><ETX>.The modem aborts playback mode immediately in two other situations:
		during a AT+VIT=m time-out or a DTR toggle. The modem immediately aborts playback mode if
		+VIT≠0 and the modem has not received any data or if the modem receives a <DLE><NUL> code
		before the +VIT timer time-out. The modem then hangs up the line and switches to data mode
		(+FCLASS=0). If the UART DTR signal is toggled from on-off-on, then the modem follows the &Dn
		setting. If configured for &D2 or &D3, then the modem immediately aborts playback mode, hangs up
		the line, and switches to data mode (+FCLASS=0).
		NOTE: The voice sampling rate and sampling mode must be the same values used during record
		mode.
NOTE: An asterisk (*) denotes the factory-default setting.

84 536EX Chipset Developer’s Manual

Intel Confidential