Jensen MP6612i manual System Menu Operation, Clock Set

MP6612i

Subwoofer (SUB-W)

To adjust Subwoofer options, press the MENU button (22) until “SUB-W” appears in the display. Press the TUNE/TRACK >> or << buttons (19) to access the following settings:

•SUB-W

Turn the rotary encoder to turn the subwoofer feature ON/OFF.

•LEVEL

The sub-woofer level control is only applicable if the unit is connected to an optional sub-woofer speaker. Turn the rotary encoder to turn the subwoofer ON/OFF or adjust the sub-woofer level from “00” to “12”.

•Sub-woofer Low Pass Filter (LPF)

The sub-woofer LPF control is only applicable if the unit is connected to an optional sub-woofer speaker and a subwoofer level is selected. Turn the rotary encoder to select one of the following four Low Pass Filter options: Flat, 80Hz, 120Hz, 160Hz. (“Flat” turns the LPF off, allowing the sub-woofer to play full range.)

Balance (BAL/FAD)

To adjust the balance from “L10” (full left) to “R10” (full right), press the MENU button (22) until “BAL/FAD” appears in the display. Press the TUNE/ TRACK >> or << buttons (19) to adjust the balance between the left and right speakers. “C00” represents a center balance.

Fader (BAL/FAD)

To adjust the fader from “F10” (full front) to “R10” (full rear), press the MENU button (22) until “BAL/FAD” appears in the display. Turn the rotary encoder to adjust the fader between the front and rear speakers. “C00” represents a center fader level.

System Menu Operation

Press and hold the MENU button (22) for more than two seconds to access the SYSTEM menu. Press the MENU button repeatedly or use the TUNE/ TRACK >> or << buttons (19) to move through the following menu options: Time Format, VOL SEL, BEEP, Area, LOCAL, Bright, LCD Mode, Screen Save. The following procedures assume you have already accessed the menu.

Time Format

This option allows selection of a 12 hour or 24 hour clock format. “12 HOUR” is the default setting. Turn the rotary encoder to change to the 24 hour clock format.

Programmable Turn-on Volume Level (VOL SEL)

Press the MENU button (22) to select “Last” or “Adjust”.

•Last

When the unit is turned on, the volume will resume at the level selected when last turned off.

•Adjust

After selecting “Adjust”, press the MENU button to select “Volume PGM” and then turn the rotary encoder (22) to select the desired turn- on level (0-46). When this option is selected, the unit will revert to the adjusted volume each time the unit is turned on.

BEEP

Turn the rotary encoder to select “ON” or “OFF”. When “ON” is selected, an audible beep tone is heard each time a button is pressed on the face of the radio. “BEEP ON” is the default setting.

Frequency Spacing (Area)

This option allows you to select the appropriate frequency spacing for your area. “U.S.A.” is the default setting. Turn the rotary encoder to select “EUROPE”, if needed.

LOCAL

Turn the rotary encoder to turn local radio reception “ON” or “OFF”. When the Local function is on, only radio stations with a strong signal are played.

Bright

This option allows you to adjust the brightness of the LCD screen. Turn the rotary encoder to select a brightness level between “01” and “08”, with “08” being the brightest.

LCD Mode

Turn the rotary encoder to select “Normal” or “Reverse”, depending on personal preference. “Reverse” will reverse the black and white pixel display.

Screen Save

Turn the rotary encoder to select “ON” or “OFF”. When “ON” is selected, the screensaver will appear after 5 seconds of inactivity, allowing your music to continue playing.

Clock Set

1.Press and hold the DISP button (18) until the clock blinks.

2.Turn the rotary encoder (22) to the right the set the hour and to the left to set the minutes.

9