Johnson Controls TM9V*MP Section V Electrical Power, UIM-C-0712, Electrical Power Connections

701379-UIM-C-0712

SECTION V: ELECTRICAL POWER											Field wiring to the unit must be grounded. Electric wires that are field
ELECTRICAL POWER CONNECTIONS											installed shall conform to the temperature limitation for 63°F (35°C) rise
											wire when installed in accordance with instructions. Refer to Table 7 in
											these instructions for specific furnace electrical data.
	Use copper conductors only.
	Table 7: Ratings & Physical / Electrical Data
	Input			Output			Nominal		Cabinet Width			Total Unit	AFUE	High Fire		Low Fire
	High/Low		High/Low				Airflow							Air Temp. Rise		Air Temp. Rise
												Amps
	MBH	kW	MBH		kW	CFM		m3/min	in.	cm			%	°F	°C	°F	°C
	40/26	12/8	38/25		11/7	1000		28.3	14-1/2	36.8		9	96	30 - 60	17-33	20-50	11-28
	60/39	18/11	58/37		17/11	1200		34	17-1/2	44.4		9	96	35 - 65	19-36	35-65	19-36
	80/52	23/15	77/50		22/14	1200		34	17-1/2	44.4		9	96	40 - 70	22-39	35-65	19-36
	80/52	23/15	77/50		22/14	1600		45.3	21	53.3		12	96	35 - 65	19-36	35-65	19-36
	100/65	29/19	96/62		28/18	1600		45.3	21	53.3		12	96	35 - 65	19-36	30-60	17-33
	100/65	29/19	96/62		28/18	2000		56.6	21	53.3		14	96	35 - 65	19-36	35-65	19-36
	120/78	35/23	115/75		33/22	2000		56.6	24-1/2	62.2		14	96	35 - 65	19-36	35-65	19-36
	Input		Max. Outlet				Blower		Blower Size			Max.	Min. Wire Size	Operating
	High/Low		Air Temp.									Over-current	(awg) @ 75 ft.	Weight
	MBH	kW	°F		°C	HP		Amps	in.	cm		Protect	One Way	Lbs.	Kg.
	40/26	12/8	180		82.2	1/2		7	11 x 8	27.9 x 20.3		15	14	113	51.2
	60/39	18/11	170		76.7	1/2		7	11 x 8	27.9 x 20.3		15	14	122	55.3
	80/52	23/15	175		79.4	1/2		7	11 x 8	27.9 x 20.3		15	14	126	57.1
	80/52	23/15	175		79.4	3/4		10.2	11 x 10	27.9 x 25.4		15	14	136	61.7
	100/65	23/15	175		79.4	3/4		10.2	11 x 10	27.9 x 25.4		15	14	142	64.4
	100/65	29/19	175		79.4	1		12.7	11 x 11	27.9 x 27.9		20	12	145	65.7
	120/78	35/23	170		76.7	1		12.7	11 x 11	27.9 x 27.9		20	12	156	70.7

Annual Fuel Utilization Efficiency (AFUE) numbers are determined in accordance with DOE test procedures.

Wire size and over current protection must comply with the National Electrical Code (NFPA-70-latest edition) and all local codes. The furnace shall be installed so that the electrical components are protected from water.

SUPPLY VOLTAGE CONNECTIONS

Junction

Box

Connect ground lead to screw

Electrical Entry

L1-Hot BLK

Neutral WHT

FIGURE 17: Electrical Wiring

1.Provide a power supply separate from all other circuits. Install over- current protection and disconnect switch per local/national electrical codes. The switch should be close to the unit for convenience in servicing. With the disconnect or fused switch in the OFF position, check all wiring against the unit wiring label. Refer to the wiring dia- gram in this instruction.

2.Remove the wiring box cover screws. Route all power wiring through a conduit connector or other proper bushing that has been installed into the unit opening and the junction box. In the junction box there is a black wire, a white wire and a green ground screw. Connect the power supply as shown on the unit’s wiring label located on the inside of the blower compartment door, or the wiring schematic in this section. Connect the black wire to L1 (hot) from the power supply. Connect the white wire to neutral. Connect the ground wire (installer-supplied) to the green (equipment ground) screw. An alternate wiring method is to use a field-provided 2”

(5.1 cm) x 4” (10.2 cm) box and cover on the outside of the furnace. Route the furnace leads into the box using a protective bushing where the wires pass through the furnace panel. After making the wiring connections replace the wiring box cover and screws. Refer to Figure 17.

3.The furnace's control system requires correct polarity of the power supply and a proper ground connection. Refer to Figure 17.

The power connection leads and wiring box may be relocated to the left side of the furnace. Remove the screws and cut wire tie holding excess wiring. Reposition on the left side of the furnace and fasten using holes provided.

LOW VOLTAGE CONTROL WIRING CONNECTIONS

Install the field-supplied thermostat by following the instructions that come with the thermostat. With the thermostat set in the OFF position and the main electrical source disconnected, connect the thermostat wiring from the wiring connections on the thermostat to the terminal board on the ignition module, as shown in Figures 18 - 21. Electronic thermostats may require the common wire to be connected. Apply strain relief to thermostat wires passing through cabinet. If air condition- ing equipment is installed, use thermostat wiring to connect the Y and C terminals on the furnace control board to the proper wires on the con- densing unit (unit outside).

Set the heat anticipator in the room thermostat to 0.4 amps. Setting it lower will cause short cycles. Setting it higher will cause the room temperature to exceed the set points.

Some electronic thermostats do not have adjustable heat anticipa- tors. They should be set to six cycles per hour. Follow the thermostat manufacturer's instructions.

The 24-volt, 40 VA transformer is sized for the furnace components only, and should not be connected to power auxiliary devices such as humidifiers, air cleaners, etc. The transformer may provide power for an air conditioning unit contactor.

12 Johnson Controls Unitary Products