6

01268

AB

Adjustment of the cutting unit

A. In the direction of travel

1.Check that the air pressure is correct in all four tires.

2.Make sure that the machine is on a horizontal surface.

3.Lift up the cutting unit to its highest position.

4.Measure the distances A and B.

Einstellung des Mähaggregats

A. In Fahrrichtung

1.Prüfen, daß der Luftdruck an allen vier Reifen richtig ist.

2.Prüfen, daß die Maschine auf einer ebenen Unterlage steht.

3.Mähaggregat in die oberste Lage anheben.

4.Abstände A und B messen.

Réglage du carter de coupe

A. Réglage latéral

1.Vérifi er que la pression, dans les quatre pneus, est cor- rect.

2.S'assurer que le tracteur est placé sur une surface plane.

3.Relever au maximum le carter de coupe.

4.Mesurer les distances A et B.

Ajuste de la unidad de corte

A. En el sentido de la marcha

1.Controlar que la presión de infl ado es la correcta en los cuatro neumáticos.

2.Asegurarse de que la máquina está sobre suelo hori- zontal.

3.Levantar la unidad de corte hasta su posición más el- evada.

4.Medir la distancia A y B.

Regolazione del tagliaerba

A. Nel senso di marcia

1.Controllare la pressione dei pneumatici.

2.La macchina deve essere in piano.

3.Sollevare al massimo il tagliaerba.

4.Misurare le distanze A e B.

Het instellen van de maaikast

A. In de rijrichting

1.Controleer of de luchtdruk in alle vier de banden juist is.

2.Zorg ervoor dat de machine op een vlakke ondergrond staat.

3.Zet de maaikast in de hoogste stand.

4.Meet de afstanden A en B.

2

1

To achieve best cutting results the cutting unit’s front edge (B) should be about 10 mm (0.375") lower than the back edge

(A). Adjust in the following way to raise the back edge:

1.Loosen the nut (1) on both the left and right levers.

2.Screw the nut (2) the same number of turns on both levers.

3.When the correct distance (A) is obtained this setting is locked with the nut (1).

Für bestes Mähergebnis muß die Vorderkante des Mähag- gregats (B) ca. 10 mm tiefer liegen als die Hinterkante (A). Einstellung zur Erhöhung der Hinterkante:

1.Mutter (1) am linken und rechten Hebel lösen

2.Mutter (2) gleich viele Drehungen an beiden Hebeln verstellen.

3.Wenn der richtige Abstand (A) erhalten wird, sind die Einstellungen mit der Mutter (1) zu sperren.

Pour obtenir la coupe la meilleure, le bord avant du carter de coupe (B) doit être situé à 10 mm au-dessous du plan du bord arrière (A). Pour régler la position du bord arrière, procéder de la manière suivante :

1.Desserrer l'écrou (1) sur les biellettes de suspension avant, droite et gauche, du carter de coupe.

2.Visser les écrous (2) exactement de la même façon sur les biellettes de suspension avant, droite et gauche.

3.Lorsque la distance (A) est correcte, verrouiller ce réglage en resserrant l'écrou (1).

Para obtener el mejor resultado de corte, el extremo delantero

(B)de la unidad de corte ha de estar unos 10 mm (0,375") más bajo que el extremo posterior (A). Ajustar de la manera siguiente para elevar el extremo posterior:

1.Quitar la tuerca (1) en las palancas izquierda y dere- cha.

2.Enroscar la tuerca (2) el mismo número de vueltas en las dos palanca.

3.Cuando se ha obtenido la distancia correcta (a), el ajuste se bloquea con la tuerca (1).

Per ottenere i migliori risultati, il bordo anteriore del tagliaerba

(B)deve essere circa 10 mm più basso di quelo anteriore

(A).Regolare nel modo sequente:

1.Allentare il dado (1) sui bracci destro e sinistro.

2.Avvitare il dado (2) di un nuemero identico di giri sui due bracci.

3.Dopo aver raggiunto la distanza corretta (A) bloccare stringendo il dado (1).

Om het beste maairesultaat te bereiken, dient de voorkant

(B)van de maaikast ca. 10 mm (0,375") lager te staan dan de achterkant (A). Ter verhoging van de achterkant als volgt instellen:

1.Draai moer (1) los op linker en rechter hefboom.

2.Draai moer (2) op de beide hefbomen evenveel slagen.

3.Wanneer de juiste afstand (A) is bereikt, wordt de instel- ling met de moer (1) vastgezet.

57

Page 57
Image 57
Jonsered LT2118A Adjustment of the cutting unit, Einstellung des Mähaggregats, Réglage du carter de coupe

LT2118A specifications

The Jonsered LT2118A is a robust and efficient lawn tractor designed to meet the needs of both residential and semi-professional users. Equipped with a powerful engine and advanced technology, this model provides an outstanding mowing experience, making it a preferred choice for homeowners and landscape enthusiasts.

At the heart of the LT2118A is its reliable 18.5 HP Briggs & Stratton V-Twin engine. This engine not only ensures powerful performance but also provides a smooth and quiet operation. It is designed for optimal fuel efficiency, allowing users to cover large areas without frequent refueling. The engine's design minimizes vibrations and noise, contributing to a more enjoyable mowing experience.

One of the standout features of the Jonsered LT2118A is its 42-inch cutting deck. This cutting deck enables users to navigate through tight spaces while still delivering a wide cutting path for efficient mowing. The deck offers multiple cutting heights, allowing for precise adjustments to achieve the desired grass height. The deck’s robust construction ensures durability, while the anti-scalp wheels prevent damage to the lawn surfaces.

Another significant aspect of the LT2118A is its Hydrostatic transmission system. This technology provides seamless speed control and easy maneuverability. With no gears to shift, riders can easily adjust their speed while maintaining control over the tractor. This is a notable advantage for mowing on uneven terrain or around obstacles.

Additionally, the Jonsered LT2118A features ergonomic controls and a comfortable seat designed for prolonged use. The high-back seat provides support while reducing fatigue during long mowing sessions. The intuitive layout of the controls allows for easy access to essential functions, making it user-friendly even for beginners.

Safety is also a priority with the LT2118A. This model includes features such as an automatic blade brake that engages when the operator leaves the seat. This ensures that the blades stop quickly, reducing the risk of accidents.

In summary, the Jonsered LT2118A is a versatile lawn tractor that combines power, efficiency, and comfort. With its strong engine, advanced transmission, and user-friendly design, it is an ideal choice for anyone looking to maintain their lawn with ease and precision. Whether tackling large yards or navigating through complex landscaping, the LT2118A stands out as a reliable and effective solution for outdoor maintenance.