6

 

00598

1

1

“A”“A”

01553

2

(1) Bottom edge of mower

(2) Lift link adjustment nut

(1) Unterkante des Mähwerks

(2) Hubstangen-Stellmutter

(1) Extrémités du carter de coupe

(2) Ecrou de réglage du bras de suspension arrière

(1) Parte inferior de la esquina de la segadora

(2) Tuerca de ajuste del várillaje de levantamiento

(1) Bordo inferiore del tagliaerba

(2) Dado di regolazione dell'articolazione di sollevamento

(1) Onderkant van de maaimachine

(2) Bijstelmoer

SIDE-TO-SIDE ADJUSTMENT

Raise mower to highest position.

At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” should be the same or within 6mm (1/4") of each other.

If adjustment is necessary, make adjustment on one side of mower only.

To raise one side of mower, tighten lift link adjustment nut on that side.

To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

Recheck measurements after adjusting.

SEITLICHE EINSTELLUNG

Das Mähwerk auf die höchste Position einstellen.

Auf beiden Seiten des Mähwerks in der Mitte den Ab- stand von der Unterkante des Mähwerks zum Boden messen. Der Abstand “A” sollte auf den beiden Seiten um höchstens 6 mm (1/4') voneinander abweichen.

Falls eine Einstellung notwendig sein sollte, die Einstel- lung nur auf einer Seite des Mähwerks vornehmen.

Um eine Seite des Mähwerks anzuheben, die Hubstan- gen-Stellmutter auf der jeweiligen Seite festziehen.

Um eine Seite des Mähwerks abzusenken, die Hubstan- gen -Stellmutter auf der jeweiligen Seite lösen.

HINWEIS: Drei volle Umdrehungen der Stellmutter verändern die Höhe des Mähwerks um etwa 3 mm (1/8").

Nach der Einstellung die Abstände erneut prüfen

REGLAGE TRANSVERSAL

Relever le carter de coupe au maximum.

A partir du milieu de chaque extrémités latérales du carter de coupe, mesurer la distance du bord du carter par rap- port au sol .

La distance (A) doit être la même des deux côtés à 6 mm près.

Si un réglage est nécessaire, ne l'effectuer que d'un seul côté en se référant à l'autre côté.

Abaisser ou soulever un côté du carter de coupe en ajustant la position de l'écrou de réglage de ce côté.

REMARQUE : A trois tours complets de l'écrou de réglage correspond une variation de la hauteur au-dessus du sol, du carter de coupe, de 0,3 cm.

Contrôler à nouveau la distance au sol après chaque opération de réglage.

ADJUSTE DE LADO A LADO

Levante la segadora a su posición más alta.

A media distancia de ambos lados de la segadora, mida la altura desde la parte inferior del extremo de la segadora al suelo. La distancia “A” debe ser la misma o dentro de 6mm (1/4") de la una a la otra.

Si el ajuste es necesario, haga el ajuste en un lado de la segadora solamente.

Levante un lado de la segadora por apretar la tuerca de ajuste del várillaje de levantamiento en ese lado.

Baje un lado de la segadora por desapretar la tuerca de ajuste del várillaje de levantamiento en ese lado.

NOTA: Cada tres vueltas completas de la tuerca de ajuste cambiará la altura de la segadora en aproximadamente (1/8").

Vuelva a revisar las medidas después del adjuste.

REGOLAZIONE FIANCO A FIANCO

Alzare il tagliaerba nella posizione più alta.

Sui punti centrali di entrabi i lati del tagliaerba, misurare l'altezza dal bordo inferiore del tagliaerba al suolo. La distanza “A” deve essere la stessa o diversa non più di circa 6mm (1/4 di pollice).

Se necessario, fare la regolazione su un solo lato del tagliaerba.

Per alzare un lato del tagliaerba, stringere il dado di regolazione dell'articolazione di sollevamento su quel lato.

Per abbassare un lato del tagliaerba, allentare il dado di regolazione dell'articolazione di sollevamento su quel lato.

NOTA: Tre giri completi del dado di regolazione cambiano l'altezza del tagliaerba di circa 3 mm (1/8 di pollice).

Dopo aver fatto la regolazione, ricontrollare le misura- zioni.

LINKS/RECHTS BIJSTELLEN

Zet de maaimachine in de hoogste stand.

Meet vervolgens in het midden tussen beide zijkanten van de maaimachine de hoogte van de onderkant van de maaimachine tot de grond. Afstand “A” moet ofwel hetzelfde zijn, ofwel binnen 6 mm (1/4") van elkaar lig- gen.

Indien bijstellen nodig is, mag dit slechts aan één kant van de maaimachine gebeuren.

Draai de bijstelmoer vaster aan de kant van de maaima- chine die u hoger wilt instellen.

Draai de bijstelmoer looser aan de kant van de maaima- chine die u lager wilt instellen.

N.B.: Drei slagen van de bijstelmoer veranderen de hoogte ongeveer 3 mm (1/8").

Controleer na het bijstellen de hoogte opnieuw.

58

Page 58
Image 58
Jonsered LT2118A SIDE-TO-SIDE Adjustment, Seitliche Einstellung, Reglage Transversal, Adjuste DE Lado a Lado

LT2118A specifications

The Jonsered LT2118A is a robust and efficient lawn tractor designed to meet the needs of both residential and semi-professional users. Equipped with a powerful engine and advanced technology, this model provides an outstanding mowing experience, making it a preferred choice for homeowners and landscape enthusiasts.

At the heart of the LT2118A is its reliable 18.5 HP Briggs & Stratton V-Twin engine. This engine not only ensures powerful performance but also provides a smooth and quiet operation. It is designed for optimal fuel efficiency, allowing users to cover large areas without frequent refueling. The engine's design minimizes vibrations and noise, contributing to a more enjoyable mowing experience.

One of the standout features of the Jonsered LT2118A is its 42-inch cutting deck. This cutting deck enables users to navigate through tight spaces while still delivering a wide cutting path for efficient mowing. The deck offers multiple cutting heights, allowing for precise adjustments to achieve the desired grass height. The deck’s robust construction ensures durability, while the anti-scalp wheels prevent damage to the lawn surfaces.

Another significant aspect of the LT2118A is its Hydrostatic transmission system. This technology provides seamless speed control and easy maneuverability. With no gears to shift, riders can easily adjust their speed while maintaining control over the tractor. This is a notable advantage for mowing on uneven terrain or around obstacles.

Additionally, the Jonsered LT2118A features ergonomic controls and a comfortable seat designed for prolonged use. The high-back seat provides support while reducing fatigue during long mowing sessions. The intuitive layout of the controls allows for easy access to essential functions, making it user-friendly even for beginners.

Safety is also a priority with the LT2118A. This model includes features such as an automatic blade brake that engages when the operator leaves the seat. This ensures that the blades stop quickly, reducing the risk of accidents.

In summary, the Jonsered LT2118A is a versatile lawn tractor that combines power, efficiency, and comfort. With its strong engine, advanced transmission, and user-friendly design, it is an ideal choice for anyone looking to maintain their lawn with ease and precision. Whether tackling large yards or navigating through complex landscaping, the LT2118A stands out as a reliable and effective solution for outdoor maintenance.