Connecting to Various Devices

*Before connection, be sure to turn off the projector and connected devices.

*Read the manual which comes with each device thoroughly.

Signals that Can Be Input to the Projector

The following signals can be input to the projector:

■Video signals

(1) Response to color systems

Color system

NTSC 480i

NTSC 4.43

PAL

SECAM

Input terminal

 

 

 

 

 

 

 

 

 

VIDEO*3

‡

‡

‡

‡

Y/C*3

‡

‡*1

‡

-----

 

 

 

 

 

Y, PB/B-Y, PR/R-Y

‡*1

‡*2

‡*2

‡*2

 

 

 

 

 

G, B, R, H/CS, V

‡*2

‡*2

‡*2

‡*2

*1: Responds if Y/C output is available.

*2: Signifies that component signals (“Y, PB, PR” / “Y, B-Y, R-Y” / “G, B, R, H/CS, V”) conform to the signal timing (synchronization and video period) of each color system. The color systems are used for convenience only.

*3: To use these terminals, a video board (separately sold) is required.

(2) Response to double density (*1), high-vision signals

Input terminal

NTSC*2

High-vision signal

Y, PB/B-Y, PR/R-Y

‡

‡

 

 

 

G, B, R, H/CS, V

‡

‡

 

 

 

*4: Signals whose density of scanning lines/field is twice as high.

*5: Responds to signals whose horizontal scanning frequency is 31.5 kHz. NTSC can be made twice as dense by a line doubler (separately available: recommended article). Also, possible to respond to fully-specified, decoded 525P progressive signals.

Note

•DTV-format signals (480i, 480p, 720p, 1080i) can be input into this unit (Y, PB/B-Y, PR/R-Y input terminals). For details about DTV-format signals (480i, 480p, 720p, 1080i) compatible with this unit, refer to page 65.

■Computer signals

•Signals with the following resolutions can be input to the input terminal of RGB IN-1 (PC) or RGB IN-2 (G, B, R, H/CS, V). (The following signals are preset.)

Screen resolution (standard name)

Horizontal frequency

Vertical frequency

Scanning method

 

 

 

 

 

640

⋅ 400 (PC-9801)

24.8kHz

56.4Hz

Non-interlace

 

 

 

 

 

640

⋅ 350 (VGA1)

31.5kHz

70.1Hz

Non-interlace

 

 

 

 

 

640

⋅ 480 (VGA3)

31.5kHz

59.9Hz

Non-interlace

 

 

 

 

 

640

⋅ 480 (Macintosh 13")

35.0kHz

66.7Hz

Non-interlace

 

 

 

 

 

 

640

⋅ 480

(VGA VESA)

37.5kHz

75.0Hz

Non-interlace

 

 

 

 

 

 

800

⋅ 600

(SVGA1)

37.9kHz

60.3Hz

Non-interlace

 

 

 

 

 

 

800

⋅ 600

(SVGA2)

48.1kHz

72.2Hz

Non-interlace

 

 

 

 

 

 

832

⋅ 624

(Macintosh 16")

49.7kHz

74.6Hz

Non-interlace

 

 

 

 

 

 

1024

⋅ 768

(XGA1)

48.4kHz

60.0Hz

Non-interlace

 

 

 

 

 

 

1024

⋅ 768

(XGA2)

56.5kHz

70.1Hz

Non-interlace

 

 

 

 

 

 

1024

⋅ 768

(Macintosh 19")

60.2kHz

74.9Hz

Non-interlace

 

 

 

 

 

 

1152

⋅ 870

(Macintosh 21")

68.7kHz

75.0Hz

Non-interlace

 

 

 

 

 

1280

⋅ 1024 (SXGA1)

64.0kHz

60.0Hz

Non-interlace

 

 

 

 

 

1280

⋅ 1024 (SXGA2)

70.8kHz

67.0Hz

Non-interlace

 

 

 

 

 

1360

⋅ 1024 (SXGA3: Mac Board)

80.0kHz

75.1Hz

Non-interlace

 

 

 

 

 

 

 

 

Notes

•Interlace signals are not handled.

•Some signals other than listed above can be displayed. But they require adjustment. Even some of the signals listed above may require adjustment depending on the video board used.

•When a signal other than listed above is input, the screen could be partially erased or an unneeded fold-over screen could appear.

•Even signals in the frequency range that can be input may not be displayed normally depending on the type of the signal.

•Composite sync.(CS) and G on sync. signals can not handled depending on the devices connected.

18