JVC DT-V17L2D manual Setting of sub menu Posi, Function Setting, Picture SUB ADJ, Size/Posi. Adj

Menu Configuration—SET-UP MENU

For the operation procedure, see page 7.

Operation guide Shows the buttons for each operation.

• The menu automatically disappears in about 30 seconds after the previous operation.

• Some items may not appear on the menu depending on the input or the input signal.

• The items controlled by the MAKE system do not appear on the menu.

NOTE

Setting of “sub menu POSI.”

The setting values and features are as follows.

LOWER1: Displays the current setting and adjustment bar at the lower part of the screen.

UPPER1: Displays the current setting and adjustment bar at the upper part of the screen.

LOWER2: Displays the current setting at the lower part of the screen.

UPPER2: Displays the current setting at the upper part of the screen.

12

FUNCTION SETTING

Setting for the sub menu display, color system, and color of the tally lamp

Item	To do	Setting value
sub menu POSI.	Select the contents and displaying position of “sub menu.”	☞ “NOTE”
COLOR	Select the color system.	AUTO, NTSC, PAL
SYSTEM	• If the picture is unstable with “AUTO,” select “PAL” or “NTSC.”
TALLY SELECT	Select the color of the tally lamp.	GREEN, RED

PICTURE SUB ADJ.

Adjusts the standard level for the picture adjustment and selects the set-up level for the input video signal.

Item	To do	Setting value
CONTRAST*1	Adjust the standard level for the contrast adjusted	–20 – +20
	with CONTRAST knob on the front panel.
BRIGHT*1	Adjust the standard level for the brightness	–20 – +20
	adjusted with BRIGHT knob on the front panel.
CHROMA*1	Adjust the standard level for the chroma adjusted	–20 – +20
	with CHROMA knob on the front panel.
PHASE*1	Adjust the standard level for the phase adjusted	–20 – +20
	with PHASE knob on the front panel.
NTSC SETUP	Select the set-up level of the input NTSC signal.	00 (compliant with 0% set-up signal), 7.5 (compliant
		with 7.5% set-up signal)
COMPO.	Select the level of the analog component signal	SMPTE (compliant with M2VTR signals), B75
LEVEL	(480i and 576i only).	(compliant with BetacamVTR 7.5% set-up signal),
		B00 (compliant with BetacamVTR 0% set-up signal)
sub menu	Display the sub menu which enables you to adjust the items in “PICTURE SUB ADJ.” while viewing the
	actual picture.
reset	Restore the default settings for all the items in “PICTURE SUB ADJ.”

SIZE/POSI. ADJ.

Adjusts the size and position of the picture.

Item	To do	Setting value
H SIZE*2	Adjust the horizontal picture size.
H POSITION*2	Adjust the horizontal picture position.	Setting value varies depending on
V SIZE*2	Adjust the vertical picture size.	the signals.
V POSITION*2	Adjust the vertical picture position.
sub menu	Display the sub menu which enables you to adjust the items of “SIZE/POSI. ADJ.” while viewing the
	actual picture.
reset	Restore the default settings for all the items in “SIZE/POSI. ADJ.”

WHITE BALANCE SET.

Selects the color temperature and adjusts the drive level and cutoff point of each color (R/G/B).

Item	To do	Setting value
COLOR TEMP.	Select the color temperature.	6500K, USER, 9300K
R DRIVE, G DRIVE,	Adjust the drive level of each color (red, green, and	MIN – 000 – MAX (in 256
B DRIVE*3	blue).	grades)
R CUT OFF, G CUT	Adjust the cutoff point of each color (red, green, and	MIN – 000 – MAX (in 256
OFF, B CUT OFF*3	blue).	grades)
sub menu	Display the sub menu which enables you to adjust the items in “WHITE BALANCE SET.”
	while viewing the actual picture.
reset	Restore the default settings for the drive levels and cutoff points of the selected color
	temperature.

*1 Memorized for each input.

*2 Memorized for each signal format.

*3 Memorized for each color temperature.

• The adjustment bar is not displayed for some items.