JVC DT-V1900CG manual HOW TO USE “SETUP MENU” contd,  Item Contents And Adjustment Range/Settings

HOW TO USE “SETUP MENU” (cont'd)

ITEM CONTENTS AND ADJUSTMENT RANGE/SETTINGS

1. FUNCTION SETTING
Selects the colour system and		<FUNCTION SETTING>
displays the monitor’s power-up		COLOR SYSTEM	:AUTO
		SYNC SELECT	:AUTO
time or the total usage time.		RUSH DELAY TIME	:STD.
		TALLY SELECT	:GREEN
Press the	button to display	REMOTE SYSTEM	:MAKE
		EMBEDDED	:1G
the setting menu illustrated on		HOUR METER X100h	:000
the right.		EXIT: MENU ADJUST:- + SELECT:
Item	: COLOR SYSTEM
Settings	: AUTO/NTSC/PAL
Function	: Selects the colour system when using the video
	input card.

AUTO : Change NTSC and PAL automatically.

NTSC : Keeps the colour system NTSC.

PAL : Keeps the colour system PAL.

NOTE : Normally select AUTO. However, if the input signal is unstable, select NTSC or PAL.

Item	: SYNC SELECT
Settings	: AUTO/INT.
Function	: Select the detection method for synchronised
	signals.
	AUTO : If a synchronised signal is input from
	external synchronised signal terminals,
	the input video signal is synchronised
	with it. If no synchronised signal is input,
	the input video signal is synchronised
	with its own built-in sync signal.
	INT. : The input video signal is always
	synchronised with the built-in sync signal.

*The external synchronised signal terminals apply to the HD/ CS terminal and VD terminal (in the RGB/COMPONENT Input Card), or the EXT. SYNC terminal (in the VIDEO Input Card).

Item	: RUSH DELAY TIME
Settings	: STD./SLOW
Function	: Sets the time when the power supply to the
	monitor’s circuits (excluding the micro computers)
	starts after the power switch is pressed.
	STD. : The power supply starts approx.
	1 second after the power switch is
	pressed.
	SLOW : The power supply starts approx.
	3.2 seconds after the power switch is
	pressed.

NOTE : When turning on many Multi-Format Monitors simultaneously, it is recommended to use SLOW to control rush current.

Item	: TALLY SELECT
Settings	: GREEN/RED
Function	: Selects the colour of the tally lamp (when lit) on

the upper front panel.

GREEN: The tally lamp lights in green.

RED : The tally lamp lights in red.

NOTE : Set the MAKE/TRIGGER terminal’s tally control in the REMOTE (external control) terminal setup menu. For details, refer to Page 20. To set the color, use TALLY SELECT in the "FUNCTION SETTING" setup menu or MAKE/TRIGGER in the REMOTE (external control) terminal setup menu. For details, refer to Page 16 and 20.

Item	: REMOTE SYSTEM
Settings	: MAKE/TRIGGER
Function	: Selects the contact system (MAKE (make

contact) or TRG. (trigger contact)) for the MAKE/ TRIGGER terminals.

MAKE (make contact system): Controls the

			function by stable disconnection (terminal
			open) or short-circuit (short with GND of 15th
			terminal) of the controlled terminal.
		TRG. (trigger system): Controls the function by
			instantaneously (one second) short-circuiting
			(short with GND of 15th terminal) the
			controlled terminal.
Item	: EMBEDDED
Settings : 1G/2G/1-2G
Function	: Selects AES/EBU Embedded Audio signal
		channels.

NOTE: The auto setting mixes and outputs all 8 signal channels. Output level is automatically detected and set at FPGA according to the channel numbers that are receiving signals.

* About sound output level

Sound output level is set to a standard output level for all channels when several sound channels are output at the same time. The more channels are selected, the lower each channel’s level will be.

(Each channel's level becomes half for 1– 2 channel, 1/4 for 1– 4 channel.)

*About AUTO

When AUTO is selected, the number of sound channels in use is detected. The level of each channel is automatically adjusted to ensure that the total sound output level is equiva- lent to the standard output level.

Item	: HOUR METER X100h
Number
range	: 000 ~ 655
Function	: Displays the total usage time of the monitor in
	hundred-hour units.

●When the timer passes 655, it returns to 000.

●The timer does not count the usage time under one hour.

2.PICTURE SUB ADJ.

Performs approximate

adjustments using the control	<PICTURE SUB ADJ.>
knobs on the front panel. Press	CONTRAST	: 00
the button to display the	BRIGHT	: 00
	CHROMA	: 00
setting menu illustrated on the	PHASE	: 00
	NTSC SETUP	: 00
	COMPO.LEVEL	:SMPTE
right.
	sub menu
	reset
NOTE : When the RGB signal	EXIT: MENU ADJUST:- + SELECT:
is input, only
CONTRAST and
BRIGHT are displayed. When the PAL signal is
input, only CONTRAST, BRIGHT and CHROMA are
displayed.

16