Onkyo TX-SR876 instruction manual Speaker Setup, Speaker Settings

Advanced Setup—Continued

Speaker Setup

This section explains items on the “Speaker Setup” menu.

Some of the speaker settings are set automatically by the Automatic Speaker Setup function (see page 64).

	--/--- 10			11				12
	INPUT SELECTOR
		MACRO
	1		2			3			ZONE3
		REMOTE MODE
	DVD	VCR			CD				ZONE2
					CDR/MD/DOCK					1
	TV	CABLE			NET/USB				RECEIVER
		SAT							TAPE/AMP
2-4	DIMMER								SLEEP
				ENU	M	EN
			M				U
		OP
		T
	+
	CH			ENTER					VOL
	DISC
	ALBUM
1, 5	-	G
				UIDE	IT
	PREV				EX
		SE	TUP					N
	CH				RETU
	DISPLAY								MUTING
	REC			PLAYLIST					RANDOM	1*
		SP A				SP B
		LISTENING MODE
	STEREO	SURR
	REPEAT	AUDIO			SUBTITLE				PLAY MODE	*TX-NR906 only
	PURE A	DIRECT			THX				ALL ST

Speaker Settings

See “Speaker Settings” on page 61.

Speaker Configuration

These settings are set automatically by the Automatic Speaker Setup function (see page 64).

With the Speaker Configuration settings, you can specify which speakers are connected and a crossover frequency, distance, and level for each speaker.

You can choose which of the speakers you want to use with the Speakers A and Speakers B configurations, and set the crossover frequencies, distances, and levels of the front Speakers A and front Speakers B independently.

The other speakers (i.e., subwoofer, center, surround, and surround back) use the same crossover frequencies, distances, and levels for Speakers A and Speakers B.

The following crossover frequencies can be specified: Full Band, 40 Hz, 50 Hz, 60 Hz, 70 Hz, 80 Hz (THX), 90 Hz, 100 Hz, 110 Hz, 120 Hz, 130 Hz, 150 Hz, or 200 Hz.

Specify Full Band for speakers that can output low-fre- quency bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover fre- quency will then be output by the subwoofer instead of the speaker. Refer to your speakers’ manuals to deter- mine the optimum crossover frequencies.

If you’re using THX-certified speakers, specify 80 Hz (THX) for all speakers.

1

2

3

4

Press the [RECEIVER] REMOTE MODE button, and then use the remote controller’s [SP A] or [SP B] button to select Speakers A or Speakers B, respectively (TX-NR906 only).

Note:

•Speakers B cannot be selected if “Speaker Type: Front(Speaker B)” is set to “Not Use”.

•TX-SR876 continue with step 2 after press the [RECEIVER] REMOTE MODE button.

Press the [SETUP] button.

The main menu appears onscreen.

Use the Up and Down [q]/[w] but- tons to select “2. Speaker Setup”, and then press [ENTER].

The “Speaker Setup” menu appears.

2.Speaker Setup

1.Speaker Settings

2.Speaker Config

3.Speaker Distance

4.Level Calibration

5.Equalizer Settings

6.THX Audio Setup

MOVE ENTER ENTER RETURN RETURN SETUP EXIT

Use the Up and Down [q]/[w] but- tons to select “2. Speaker Con- fig”, and then press [ENTER].

The “Speaker Config” screen appears.

2–2.	Speaker Config
Subwoofer	Yes
Front	Full Band	Speaker A
Center	100Hz
Surround	100Hz
SurrBack	100Hz
SurrBack Ch	2ch
LPF of LFE	120Hz
DoubleBass	On
MOVE	VALUE	RETURN RETURN SETUP EXIT

95