REAR/SIDE VIEW

<Rear Panel>

 

<Side Panel>

 

MAKE

26

 

RS-232C

SLOT3SLOT1

SLOT2

27

30

28

MAIN POWER

29

14 COLOR OFF button/lamp

Press the COLOR OFF button. The button lights and the screen becomes monochrome. When the COLOR OFF button is pressed while lit, the light goes off and the normal screen is restored.

Use this function to confirm the noise in the brightness signal or to confirm the white balance.

NOTE: This function is invalid with the RGB-input screen.

15 SCREENS CHECK button/lamp

Press the SCREENS CHECK button. The button lights and the screen changes in the following order:

Normal screen[Red screen[Green screen

[

Blue screenp

Press the SCREENS CHECK button when the blue screen is displayed. The light goes off and the normal screen is restored.

Use this function to confirm or adjust CHROMA or

PHASE.

NOTE: This function is invalid with the RGB-input screen.

16 ASPECT button/lamp

When the ASPECT button is pressed while the screen ratio is 4:3, the button lights and the screen ratio changes to 16:9. When the ASPECT button is pressed while lit, the light goes off and the normal screen is restored.

NOTE: This function is invalid with the RGB-input screen.

17 AREA MARKER button/lamp

When the AREA MARKER button is pressed while the screen ratio is 16:9, the button lights and the white marker is displayed. This shows the screen size (area) set on the menu. When the AREA MARKER button is pressed while lit, the light goes off and the normal screen is restored.

NOTE: This function is invalid with the RGB-input screen.

18 – 23 INPUT SELECT buttons/lamps

Press the unlit button. The button lights and the input signal is changed. (any other lit button goes off.) When the lit button is pressed, the status of the current input signal is displayed (for approx. 3 seconds). Buttons A through F correspond to the signals input via the input cards installed in SLOT 1 through SLOT 3.

A, B : select the picture from the SLOT 1 input card.

C, D : select the picture from the SLOT 2 input card.

E, F : select the picture from the SLOT 3 input card.

Refer to pages 6 and 8 for correspondence between the input terminals and the INPUT SELECT buttons.

24 Power lamp

Unlit : The main power is OFF.

Orange : The main power is ON, but the monitor’s power is OFF (in stand-by mode).

Green : The main power is ON, and the monitor’s power is ON (in normal operation mode).

25 POWER switch

Press the power switch to turn the monitor’s power ON or OFF when the main power is ON.

NOTE: When RUSH DELAY TIME is set to SLOW in the set-up menu, it takes approx. 3.2 seconds for the power to actually turn ON after the power switch is pressed.

26 REMOTE (external control) terminals

Terminals for controlling the monitor from an external unit. MAKE/TRIGGER terminal (Upper):

Enables the monitor to be controlled by closing the circuit (point of contact) connected to the terminal.

RS-232C terminal (Lower):

Enables the monitor to be controlled from a personal computer via serial communication.

27 Input card slots (SLOT 1 — SLOT 3)

Optional input cards can be installed in these slots. Input cards are not provided when you purchase the monitor. NOTE: It is not possible to input video or audio signals to

the monitor when no input cards are installed.

28 Main power switch

Press the switch to turn the main power ON or OFF. When the main power is ON, the power lamp on the front panel lights in yellow and the monitor enters the stand-by mode.

I : ON  : OFF

29 AC inlet

Power input connector. Connect the provided AC power cord to an AC outlet (120 V/230 V AC, 50 Hz/60 Hz).

*Attach the provided Power Cord Holder to the AC inlet to prevent accidental disconnection of the AC power cord. Refer to page 10 for details.

30 Built-in speaker (monaural)

Outputs the input audio.

ENGLISH

5

Page 6
Image 6
JVC DT-V1900CG Aspect button/lamp, Area Marker button/lamp, 18 23 Input Select buttons/lamps, Power lamp, Power switch