JVC DT-V2000SU manual HOW to Handle Basic Operations

HOW TO HANDLE BASIC OPERATIONS

BASIC OPERATION

1. Press the POWER		OFF switch to
		ON
turn on the power.		POWER
ON (_)	: Power turns ON. (Power indicator lights in
	green.)
OFF (—)	: Power turns OFF. (Power indicator goes out.)

Selected Input Display (Mode)

Display	Input
INPUT A (RGB)	RGB input
INPUT A (COMPO.)	COMPONENT input
INPUT B (VIDEO)	VIDEO input

*The frequency of the input signals (or the color system or DTV format) is automatically identified and displayed for about three seconds.

Input display

ＩＮＰＵＴ Ａ（ＲＧＢ）pＩｎｐｕｔ ｄｉｓｐｌａｙ� ４９ｋＨｚ ７５ＨｚpＦｒｅｑｕｅｎｃｙ�

（ ｏｒ ｃｏｌｏｒ ｓｙｓｔｅｍ）� ｄｉｓｐｌａｙ�

Frequency

(or color system or DTV format) display

INPUT B (Y/C)	Y/C input
INPUT C	RGB (PC) input

Input Signal Frequency/Color System/DTV Format Display

Display	Input signal
NTSC	NTSC, B/W *1
1080i	HDTV format for DTV

2. Press the INPUT SELECT

ABC

buttons to choose the

INPUT SELECT

input.

A: INPUT A input mode

(INPUT A indicator lights in green)

B: INPUT B input mode

(INPUT B indicator lights in green)

C: INPUT C input mode

(INPUT C indicator lights in green)

*When the input mode is changed or the power is turned on, the selected input and frequency (or color system or DTV format) are automatically identified and displayed for about three seconds.

3.Press the VOLUME/ENTER

buttons to adjust the

VOLUME/ENTER

speaker volume.

+: The built-in speaker volume is increased. (00 [ 50)

– :The built-in speaker volume is decreased. (50 [ 00)

* The screen indication disappears after about three seconds.

�
�
ＶＯＬＵＭＥ	：	２５�

720p	HDTV format for DTV
480p	SDTV format for DTV
480i	SDTV format for DTV
NO SYNC	No identifiable signal
OO kHz OO Hz	RGB signal at a non-preset frequency
	(Current frequency is displayed)
Out of range	Signal outside the frequency range

*1: For B/W signal, fH = 15.75 kHz, fV = 60 Hz.

Input mode and frequency (or color system or DTV format) display

●The size of the letters in the on-screen indication is auto- matically adjusted. However, the size of letters at the same frequency may change due to processing dispersion.

●The “OO kHz OO Hz” indication shown in the table above appears when the frequency is automatically identified. The horizontal frequency (kHz) and the vertical frequency (Hz) are displayed with decimal fractions omitted.

●The indicated frequency may differ from the actual frequency due to processing dispersion.

●Refer to page 14 “DISPLAY OF PRESENT INPUT STATUS” for details about the input mode and frequency (or color system or DTV format) screen.

When the POWER SAVE function is valid (ON)

●When INPUT C is selected, whenever the horizontal and vertical synchronization signals are no longer detected, the screen goes out and the POWER indicator blinks (only when the connected computer has a power management function conforming to VESA). For details about the POWER SAVE function, see page 16.

Notes:

●The monitor’s audio input level is 500 mVrms. Sound becomes distorted when a signal greater than 1 Vrms is input.

●When a DTV-format signal is displayed, noise may appear at the bottom of the screen or a signal unrelated to the picture may appear at the top or bottom. This is not a malfunction.

8