Oubleshooting, Timer again | JVC HR-DD740U instruction

56EN

TROUBLESHOOTING(cont.)

RECORDING

	SYMPTOM		POSSIBLE CAUSE		CORRECTIVE ACTION
1.	Recording won’t start.		● There’s no cassette loaded.		Insert a cassette.
			● The loaded cassette has had its		Remove the cassette and cover the
			record safety tab removed.		hole with adhesive tape, or load a
					cassette on which the record safety
					tab is intact.

2. TV broadcasts won’t record			● The VCR has been set to its AUX		Set the VCR to the appropriate
	properly.		mode by mistake.		channel.

3. Tape-to-tape editing won’t work.			●The VCRs or the camcorder and the		Refer to the directions and the
			VCR have been incorrectly con-		illustration under “Edit To Or From
			nected.		Another VCR” (☞ pg. 50) or “Edit
					From A Camcorder” (☞ pg. 48) and
					properly connect the units.
			● The power to one or more of the		Make sure the power to all units is on.
			units has not been turned on.
			● The recorder’s input mode has been		Select the recorder’s appropriate
			set incorrectly.		input mode at the Aux Input Screen
					(☞ pg. 49).

TIMER RECORDING

	SYMPTOM		POSSIBLE CAUSE		CORRECTIVE ACTION
1.	Timer recording won’t work.		● The clock and/or the timer have		Set the clock and/or timer correctly.
			been set incorrectly.
			● The timer is not engaged.		Press TIMER and check to make sure
					that TIMER appears on the front
					display panel.
			● The VCR has not been set up properly.		Re-perform the set-up procedures.
					Make sure you have compensated for
					Guide Channel and VCR or cable
					box channel number mismatches
					(☞ pg. 18).

2.	On-screen timer programming		● Timer recording is in progress.		Timer programming can’t be performed
	won’t work.				when timer recording is in progress.
					Wait until it finishes.

3.	TIMER and ] on the front		● The timer is engaged but there’s no		Load a cassette with the record safety
	display panel won’t stop blinking.		cassette loaded.		tab intact, or with the hole covered
					with adhesive tape.

4.	The cassette is automatically		● The loaded cassette has had its		Remove the cassette and cover its
	ejected, and TIMER and ] on the		record safety tab removed.		hole with adhesive tape, or replace it
	front display panel won’t stop				with a cassette on which the safety
	blinking.				tab is intact.

5. TIMER blinks for 10 seconds and			● TIMER has been pressed when there		Check the programmed data and re-
	the timer mode is disengaged.		are no programs in memory, or the		program as necessary, then press
			timer record program information		TIMER again.
			has not been programmed correctly.

6.	The cassette is automatically		● The end of tape was reached during		The program may not have been
	ejected, the power shuts off and		timer recording.		recorded in its entirety. Next time
	TIMER and ] won’t stop				make sure you have enough time on
	blinking.				the tape to record the entire program.

7. Cable channels are not automatically			● The Controller is not properly		Connect the Controller correctly
	switched during timer recording.		connected to the VCR.		(☞ pg. 15).
			● The output channel selected in the		After confirming your cable box’s
			Cable Box Output screen is incorrect.		output channel number, re-access the
					Cable Box Output screen and select
					the correct number (☞ pg. 16).
			● The cable box’s power is off.		Make sure the power is on before
					timer recording starts.

Image 56

JVC HR-DD740U manual Oubleshooting, Timer again

Contents

HR-DD740U Dear Customer Do not place the VCR Power Sources Power Cord ProtectionPower Lines Grounding or Polarization Accessories Damage Requiring ServiceCleaning Replacement Parts Contents Basic Connections Plug & Play Setup Initial SettingsPlug & Play Auto Clock Set/Auto Tuner Set Language Clock Select ScreenPreparation Time Scan %Þ, then Select Mode Access Select ScreensSelect Host Channel Semi-Auto Select D.S.T. Mode Select Time ZoneSET DATE, Time and D.S.T Make Corrections Access Main Menu Access Tuner SETTuner SET Information Access Tuner SET Screen Access AFC ScreenMake Selection Store or Skip Desired Channel Cable Box Control Situate ControllerAttach Controller Connect Cable BOX to VCR Access Custom SET Screen Access VCR PLUS+ SET-UP ScreenSelect Cable BOX Output Channel Set Cable Box Output Channel Access Cable BOX You can now set up the VCR Plus+ feature pgTurn on Cable BOX Brand SET Screen VCR Plus+ Setup VCR Plus+ Guide Channel Matching Access Custom SET Screen Input Receiving Channel Number Access Guide Channel SET ScreenSET-UP Screen Check Input Data Fasten securely using the supplied adhesive strips DBS Receiver ControlConnect DBS Receiver to VCR DBS receiver Set DBS Receiver Output Channel Press CH5 or TimeSCAN%Þ to move Highlight bar arrow to Turn on DBS Receiver Enter DBS Receiver BrandSet DBS Receiver Brand DBS Receiver Brand SET, then press OK Simple Playback Simple Recording Playback Features Pause During PlaybackActivate FRAME-BY Frame Playback Engage Manual Tracking Mode Adjust Manual TrackingLayback and Recording Features RE-ENGAGE Automatic Tracking Video Stabilizer Access Function SET Access SuperimposeReturn to Normal Superimpose Access Audio Select Access Audio MonitorSelect The Soundtrack Mix Access Distant Code Start SearchIndex Search Instant ReView Start Repeat Activate CounterMemory Return to Counter Position Zero Access Special Make ConnectionFunction Screen AV Compu Link Playback Enable AV Compu Link Playback Example Auto Picture Press Play VCR adjusts Playback picture quality PlaybackBased on the quality Tape in use Variable-Speed Search/ Reverse Motion Playback Audio signal during TimeScanTimeScan Skip Over Unwanted Sections TimeScanSkip Search Speed Audio output Access Timescan Audio ScreenTimeScan Audio CH or Time Scan Recording Features Engage TV ModeReset Counter to Zero Select Channel for Viewing Access 2ND Audio Stereo And SAP Second Audio ProgramTo Record SAP Programs To Record Stereo Programs Instant Timer Recording ITR Engage ITR ModeTimer Recording SET Recording Duration VCR Plus+ Timer Programming EN Timer Recording CHECK/CORRECT Input Data Engage Timer ModePress TIMER. The VCR turns off automatically Information On-Screen Timer ProgrammingAccess Program SET Cable BOX Output is set to OFF pg.16 To timer-record a regular TV program received on the VCRCatv Disengage Timer Access Main Menu ScreenAccess Program SET Screen Cancel a Program Or, during on-screen timer programming Access Auto TimerAuto Timer Edit From a Camcorder Make ConnectionsSET RECORDER’S Input Mode Access AUX Input Return to FunctionSET Screen Start Recorder SET RECORDER’S Input Mode Edit To Or From AnotherLoad Cassettes Start Player Special Features TV Multi-Brand Remote ControlTurn on the TV SET TV Brand Code EN Special Features Cable Box Multi-Brand Remote ControlTurn on the Cable BOX Enter Cable BOX Brand DBS Receiver Multi-Brand Remote Control Turn on the DBSReceiver Enter DBS Receiver Unplug Vcrs Power SET Remote ControlPlug in Power Cord Turn VCR Power on Cassette gets stuck partway Troubleshooting E NSet the switch to the position Timer again Oubleshooting Re-perform the VCR Plus+ setup Doesn’t work properly When scanning channels, some EN Questions and Answers Can the VCR indefinitely remain in the still mode?Can the VCR indefinitely remain in the Record-Pause mode? What happens if the tape runs out during recording? MBR Multi-Brand Remote Code Setting IndexList Of Terms Select DBS Receiver Output Channel Front View Rear View Installing Batteries How To Use Specifications HOW to Locate Your JVC Service Center For Servicing Only in U.S.A Warranty Only in U.S.A Limited Warranty EMO Memo HR-DD740U