JVC HR-J713EU Set Vps/Pdc Mode, Engage Recorder’S, Timer Mode, VPS/PDC Recording, EN25, Screen

6	ENTER CHANNEL POSITION
	Press TV PROG +/–.	– P1 –
	START	STOP
	21:00	= 22:00
	SP	VPS/PDC OFF
	DATE	TV PROG
	25.12	1
	[+/–] =	ARD
	[PROG] : EXIT
	SP

	SET TAPE SPEED
7 Press SP/LP ( ) to set the tape speed.
8	SET VPS/PDC MODE
	Press VPS/PDC to select "ON" or "OFF".
	If "VPS/PDC ON" is displayed on the screen or "VPS/
	PDC" is lit on the display panel, VPS/PDC is set to ON.
	If "VPS/PDC OFF" is displayed on the screen or "VPS/PDC"
	is not lit on the display panel, VPS/PDC is set to OFF.
	☞ "VPS/PDC Recording" in the right column.
	RETURN TO NORMAL
	SCREEN
	After confirming all information is correct, press PROG
	or OK. "PROGRAM COMPLETED" appears on the
9 screen for about 5 seconds, then normal screen
	appears.
	● Repeat steps 1 – 9 for each additional programme.
	ENGAGE RECORDER’S
10	TIMER MODE
	Press ä (TIMER). The recorder turns off automatically
	and ä appears on the display panel.
	● To disengage the timer, press ä (TIMER) again.

To Timer-Record Weekly Or Daily Serials . . .

EN25

Satellite Tuner Users

To timer-record a satellite broadcast using Express Timer Programming:

1 Set "AV2 SELECT" to "AV2" (☞ pg. 31).

2 Perform steps 1 – 10. Enter "L-2" for the channel position in step 6.

3 Set the satellite tuner to the appropriate channel before the selected programme begins.

4 Leave the satellite tuner's power on.

VPS/PDC Recording

Now available from some TV stations, PDC (Programme Delivery Control) and VPS (Video Programme System) are service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your video recorder and have precedence over the advertised times you may have preset into the timer. This means that your recorder will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed.

NOTES:

● When you use Express Timer Programming, set the start time (VPS or PDC time) exactly as advertised in the TV listing. A different time than advertised will result in no recording.

● VPS/PDC recording is also possible when a satellite tuner or a cable system is connected to AV2 IN/DECODER on your recorder.

● VPS/PDC recording is also possible via the AV1 IN/OUT connector.

How to check if the station being received transmits a VPS/PDC signal

1 Press – –:– – until the channel position appears on the display panel.

2 Hold down START+ for about 5 seconds.

● "VPS/PDC" appears blinking on the display panel. If a VPS/PDC signal is detected from the station, "VPS/ PDC" will stop blinking.

If no VPS/PDC signal is detected from the station, "VPS/

PDC" will blink at a slower rate.

3 Press – –:– – or START+ again to return to normal display.

. . . anytime during steps 2 through 9, press WEEKLY (NUMBER key “9”) for weekly serials or DAILY (NUMBER key “8”) for daily serials (Monday – Friday). Either "WEEKLY" or "DAILY" appears on the screen. Pressing the button again makes the corresponding indication disappear.

NOTE:

You can programme this recorder to timer-record as many as 8 programmes. If you try to programme the recorder to record a ninth, "PROGRAM FULL" appears on screen and "FULL" appears

Timer Warning

If you have programmed your recorder to timer-record a programme or a series of programmes, a warning appears on screen to tell you that the recording is to start in 5 minutes.

–WARNING– TIMER RECORDING

TO START SOON

[]

on the front display panel. To record the extra programme, you must first cancel any unnecessary programmes (☞ pg. 26).

NOTES:

●The warning only appears if

you’re not in the Timer mode at that time.

●If this recorder is being used as the player for tape dubbing, the warning screen is recorded on the tape in the other video recorder.

The warning blinks for the entire 5 minutes leading up to the start of timer recording. To clear the display, press .