
Fine Tune
Adjusts the pitch of the tone’s sound up or down in
VALUE:
One cent is 1/100th of a semitone.
•Creating smooth pitch transitions (Portamento)
Portamento is an effect that creates a smooth transition in pitch between one key and the next. When the Solo Switch parameter is “ON,” you can apply portamento to create an effect similar to a violinist changing the pitch smoothly by sliding their finger along the fingerboard.
Portamento Sw (Portamento Switch)
Specifies whether the portamento effect will be applied (ON) or not (OFF).
VALUE: | OFF, ON |
Portamento Time
When portamento is used, this specifies the time over which the pitch will change. Higher settings will cause the pitch change to the next note to take more time.
VALUE:
•Varying the sounds by the force of your
keyboard playing
The force with which you play a key is expressed by a velocity value. When you play a note strongly, a high velocity value will be transmitted, producing a louder volume or a different tone. By editing the Velo Sens Depth and Velo Sens Ofs values, you can adjust the relationship between your keyboard playing strength and the loudness of the notes that are produced.
Velo Sens Depth (Velocity Sensitivity Depth)
Higher settings of this value allow you to produce notes in a wider range of loudness even with small changes in your playing strength. Lower settings of this value will mean that even if you vary your playing strength significantly, the notes that are sounded will not have a wide range of loudness.
VALUE:
Velo Sens Ofs (Velocity Sensitivity Offset)
With higher settings of this value, loud sounds can be produced even when you play the keys softly. With lower settings of this value, the sounds will be soft even if you play strongly.
VALUE:
Pitch Bend Range
Specifies the amount of pitch change in semitone units (maximum of two octaves) that will occur when you operate the pitch bend lever. The amount of change will be the same whether the lever is moved to left or right.
VALUE:
Creating a patch (Patch mode)
•Adjusting the modulation of the sound (LFO)
The LFO (Low Frequency Oscillator) applies cyclic change to the sound. It can be applied to the pitch, cutoff frequency, or volume to produce vibrato, wah, or tremolo effects. The original tones of the
You cannot simultaneously adjust the pitch depth and cutoff depth. Nor can you adjust the depth of the LFO effect on volume. If you need to use an adjustable tremolo effect, use the TREMOLO
Filter LFO (Filter LFO Switch)
Selects whether the LFO Depth setting will control the depth of cutoff frequency modulation or of pitch modulation. This is linked with the operation of the [FILTER LFO] switch of the panel (p. 27).
VALUE
OFF (PCH): You can adjust the depth of the LFO’s effect on pitch.
ON (FLT): You can adjust the depth of the LFO’s effect on the filter cutoff frequency.
LFO Rate |
| Mode | |
Adjusts the modulation rate, or speed, of the LFO. This is linked | |||
Patch | |||
with the operation of the [LFO RATE] knob of the panel (p. 27). | |||
| |||
VALUE: |
|
LFO Depth
Specifies the depth of LFO. Normally, the depth of the LFO’s effect on pitch will change. If Filter LFO is ON, the LFO’s effect on cutoff frequency will change. This is linked with the operation of the [LFO DEPTH] knob of the panel (p. 27).
VALUE:
LFO Delay
Adjusts the time from when the key is pressed (or released) until the LFO begins to be applied (or the duration that the effect continues).
VALUE:
Adjusting the brightness or hardness of the sound (Filter)
The sound generator section of the
Cutoff Freq (Cutoff Frequency)
Specifies the frequency (cutoff frequency) at which the filter will begin to modify the sound. This is linked with the operation of the [CUTOFF] knob of the panel (p. 29).
VALUE:
47