Roland RS-50 owner manual FBK Ripper Feedback Ripper, 46TUMBLING DLY Tumbling Delay, TYPE1-TYPE6

Parameter	Value	Description
Reset	OFF, ON	This setting determines whether
		the period for the pattern is reset
		(ON), or not (OFF) when sounds
		are played.
		While the rhythm guide is play-
		ing, the period for the pattern is
		not reset even if you set this ON.

RESET

LEVEL

Low Gain	-15– +15 [dB]	Adjusts the gain of the low fre-
		quency.

Adding effects

Parameter	Value	Description
Balance #	D100:0W–	Adjusts the volume balance be-
	D0:100W	tween the direct sound and the
		delay sound.
		With a setting of D100:0W only the
		direct sound will be output, and
		with a setting of D0:100W only the
		delay sound will be output.
Level	0–127	Adjusts the output level.

47: FBK RIPPER (Feedback Ripper)

This effect repeatedly cuts the sound, and outputs a delayed sound for the cut portion. You can create new phrases by applying this to a drum phrase or other phrase.

fig.MFX-47

High Gain	-15– +15 [dB]	Adjusts the gain of the high fre-
		quency.
Level	0–127	Adjusts the output level.

46:TUMBLING DLY (Tumbling Delay)

This is a delay that first produces “tumbling” delayed repeats, and then echoes the original sound.

It is most effective when applied to single notes of a “one-shot” sound.

L in

Delay

Feedback

Feedback

Delay

R in

Ripper

Ripper

2-Band	L out
EQ

2-Band	R out
EQ

fig.MFX-46

L in				2-Band	L out
		Balance D		EQ
				Balance W
		Tumbling Delay		Balance W
		Feedback
R in				2-Band	R out
		Balance D		EQ
Parameter		Value	Description
Type		TYPE1–TYPE6	Selects one of the six available
			types for the number of delay
			sounds heard in time “A” in the
			diagram below.
Pre Delay		0–500 [ms]	Adjusts time “A” in the diagram
			below.
Delay Time		0–345 [ms]	Adjusts time “B” in the diagram
			below.
	Level
		original tone

A B B

HF Damp	200–8000 [Hz],	Adjusts the frequency above
	BYPASS	which sound fed back to the ef-
		fect will be cut.
		If you do not want to cut the
		high frequencies of the feed-
		back, set this parameter to BY-
		PASS.
Feedback #	-98– +98 [%]	Adjusts the proportion (%) of
		the delay sound that is fed back
		into the effect.
		Negative (-) settings will invert
		the phase.

Parameter	Value	Description
Mod Wave	TRI, SQR, SIN,	TRI: The sound will be cut by a
	SAW1/ 2	triangle wave.
		SQR: The sound will be cut by a
		square wave.
		SIN: The sound will be cut by a
		sine wave.
		SAW1/2: The sound will be cut
		by a sawtooth wave. The teeth in
		SAW1 and SAW2 point at oppo-
		site directions.
	SAW1	SAW2
Rate #	0.05–10.00 [Hz],	Adjusts the frequency (speed) of
	note *2	the change.
Depth #	0–127	Sets the depth to which the ef-
		fect is applied.
Delay Left	0–420 [ms], note	Adjusts the time from the direct
	*1	sound until the left delay sound
		is heard.
Delay Right	0–420 [ms], note	Adjusts the time from the direct
	*1	sound until the right delay
		sound is heard.
Dly Feedback	-98– +98 [%]	Adjusts the proportion (%) of
		the delay sound that is fed back
		into the effect.
		Negative (-) settings will invert
		the phase.
Reset	OFF, ON	This setting determines whether
		the period for the pattern is reset
		(ON), or not (OFF) when sounds	Effects
		While the rhythm guide is play-
		are played.
		ing, the period for the pattern is
		not reset even if you set this ON.
Level	0–127	Adjusts the output level.

85