![](/images/new-backgrounds/1278188/27818837x1.webp)
| SET TAPE SPEED | |
4 Press SP/LP ( | ) to set the tape speed. | |
5 | SET PDC MODE | |
Press PDC to select "ON" or "OFF". | ||
If "VPS/PDC ON" is displayed on the screen or "VPS/ | ||
PDC" is lit on the display panel, PDC is set to ON. | ||
| If "VPS/PDC OFF" is displayed on the screen or "VPS/ | |
| PDC" is not lit on the display panel, PDC is set to OFF. | |
| ☞ "PDC Recording" in the column below. | |
| ● VPS (Video Programme System) recording is not | |
| currently available in the U.K. and not possible with | |
| this recorder. |
|
| RETURN TO NORMAL SCREEN | |
| Press PROG or OK. "PROGRAM COMPLETED" appears | |
| on the screen for about 5 seconds, then normal screen | |
6 appears. If the timer programme is overlapped with | ||
| another one that was already set, "PROGRAM | |
| OVERLAPPED" appears on screen and "Err" appears on |
19
Satellite Receiver Users
To
1 Perform "Satellite Receiver Control Setting" (☞ pg. 12). 2 Perform steps 1 – 7. In step 3, the display panel shows "L2" for the preset position. In step 5, you cannot set
PDC to ON.
3 Leave the satellite receiver's power on.
ATTENTION
Regarding Guide Program Number Set
"GUIDE PROG SET" appears after performing step 3 if the Guide Program number for the PlusCode number you entered has not been set.
● If you want to set the Guide Program number for the satellite broadcast station, press the NUMBER key "0" to change "TV PROG" to "SAT". Press %Þ to input the preset position number on which your recorder or satellite receiver receives that station, then press OK or #to set the Guide Program Number. The VIDEO Plus+ Program screen appears.
| the front display panel. (☞ pg. 23) |
|
|
| ● Repeat steps 1 – 6 for each additional programme. |
|
|
| ENGAGE RECORDER’S TIMER |
7 | MODE |
Press ä (TIMER). The recorder turns off automatically | |
and ä appears on the display panel. | |
| |
● To disengage the timer, press ä (TIMER) again. |
GUIDE PROG SET
GUIDE PROG | TV PROG |
2 | – – |
[5°] = | [0]:SAT |
[PROG] : EXIT |
|
(Ex.) To
*If your recorder receives BBC2 on the preset position 2, press OK or #after entering "2" using %Þ buttons.
NOTES:
● To Change The Stop Time . . . |
. . . press STOP +/– after pressing OK in step 3. You can |
compensate for anticipated programme schedule delays this |
way. |
● To |
. . . after pressing OK in step 3, press WEEKLY (NUMBER key |
“9”) for weekly serials or DAILY (NUMBER key “8”) for daily |
Timer Warning
If you have programmed your recorder to
–WARNING– TIMER RECORDING
TO START SOON
[
]
serials (Monday – Friday). Either "WEEKLY" or "DAILY" |
appears on the screen. Pressing the button again makes the |
corresponding indication disappear. |
● You can programme this recorder to |
programmes. If you try to programme the recorder to record a |
ninth, "PROGRAM FULL" appears on screen and "FULL" |
appears on the front display panel. To record the extra |
programme, you must first cancel any unnecessary |
programmes (☞ pg. 22). |
● It is not possible to |
PlusCode number which starts with "0". |
NOTES:
●The warning only appears if you’re not in the Timer mode at the time.
●If this recorder is being used as the player for tape dubbing, the warning screen will be recorded on the tape in the other video recorder.
The warning blinks for the entire 5 minutes leading up to the start of timer recording. To clear the display, press .
PDC Recording
Now available from some TV stations, PDC (Programme Delivery Control) is a service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your video recorder and have precedence over the advertised times which you may have preset into the timer. This means that your recorder will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed from what has been advertised. PDC is currently available nationally on BBC1, BBC2, Ch.4 and Ch.5, except from a few small relay transmitters. Ch.3 operates a PDC service in some areas. All channels intend to offer this service in due course. Check your TV programme listing guide for latest information. If the channel you intend to record does not offer a PDC service your recorder will not start recording if PDC has been selected. Be sure to set PDC to "OFF" if PDC is not available on your selected channel (☞ step 5 above).
NOTES:
●PDC recording is also possible when a satellite receiver or a cable system is connected to AV2
●PDC recording is also possible via the AV1