PAL/MESECAM — AUTO / PAL / MESECAM
Usually set to “AUTO” mode. The appropriate colour system (PAL/ MESECAM) will be selected depending on the playback or recording signals.
If the “AUTO” mode does not work properly, select either of the following manual modes.
PAL: To record PAL signals, or playback a PAL tape.
MESECAM: To record SECAM signals, or playback a SECAM or MESECAM tape.
NOTES:
●SECAM signals will always be recorded as MESECAM. Select “AUTO” or “MESECAM” when recording SECAM signals.
●When playing back a SECAM tape, select “AUTO” or “MESECAM”. The playback picture will always be monochrome.
NTSC — NTSC3.58 / NTSC4.43 / NTSC]PAL
This function is to record NTSC signals or playback a NTSC tape. NTSC3.58: To record NTSC signals or playback a NTSC tape. NTSC4.43: To record NTSC4.43 signals or playback a NTSC4.43 tape.
NTSC]PAL: To playback a NTSC tape on PAL TV.
NOTES:
●The “NTSC]PAL” mode does not work during recording. In this mode, NTSC signals will be recorded as NTSC3.58.
●The Menu screen is distorted during playing back a NTSC tape on PAL TV. Stop playback and access the Menu screen again.
●In the “NTSC4.43” mode, with some TVs,
AUTO TIMER — ON / OFF
●When this function is set to “ON”:
The timer recording standby mode is automatically engaged when the recorder is turned off. It is temporarily cancelled when the recorder is turned on. You do not have to press # to engage or disengage the timer recording standby mode.
●When this function is set to “OFF”:
Press # to engage or disengage the timer recording standby mode.
O.S.D. — ON / OFF
When this function is set to “ON”, various recorder status information
NOTE:
When you use the recorder as the source player for editing a tape, be sure to set this function to “OFF”. Otherwise, the recorder status information will be recorded on the edited tape.
PROG. NAVIGATION — ON / OFF
When you record a TV programme with this recorder, the recorder automatically stores in its memory the recording date, start time and station name. You can store these information for up to 8 programmes on one cassette. At maximum, information for 10 tapes can be stored. You can also enter the programme title when performing
Set “PROG. NAVIGATION” to “OFF” if you don’t want to record information on the programmes.
AUTO SP]LP TIMER — ON / OFF
When this function is set to “ON”, the recorder automatically switches to LP mode to allow complete recording if there is not enough tape to record the entire programme while timer- recording in SP mode.
For example, recording a programme of 210 minutes in length onto a 180 minute tape.
Approximately 150 minutes | Approximately 60 minutes |
SP mode | LP mode |
|
|
Total 210 minutes
NOTES:
●If you have programmed the recorder to
●There may be some noise and sound disturbance where the tape speed switches from SP to LP mode on the tape.
●This function is not available during ITR (Instant Timer Recording), and will not work properly with any tapes longer than
●If you perform timer recording with both this function and VPS/ PDC activated, and the programme goes beyond its originally scheduled length, sometimes the programme cannot be recorded in its entirety.
VIDEO STABILIZER — ON / OFF
When this function is set to “ON”, you can automatically correct vertical vibrations in the picture when playing back unstable recordings made on another recorder.
NOTE:
To watch recordings with
S-VHS — 0N / OFF
You can determine which recording mode — either
●When this function is set to “ON”, you can record on
●When this function is set to “OFF”, you can record on
NOTES:
●
●
Recording on VHS tapes is always performed in VHS mode except when using
— 16 —