Recording | JVC LPT0328 specs

			EN 83
RECORDING
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1.	Recording cannot be started.	● There is no cassette loaded, or the	Insert a cassette, or using adhesive tape,
		cassette loaded has had its record safety	cover the hole where the tab was
		tab removed.	removed.

2.	TV broadcasts cannot be recorded.	● “L-1”, “L-2”, “F-1”, “S-1” or “SAT” has	Set to the desired channel.
		been selected as the input mode.

3.	Tape-to-tape editing is not possible.	● The source (another video recorder,	Confirm that the source is properly
		camcorder) has not been properly	connected.
		connected.
		● All necessary power switches have not	Confirm that all units’ power switches are
		been turned on.	turned on.
		● The input mode is not correct.	Set the input mode to “L-1”, “L-2”, “F-1”
			or “S-1”.

4.	Camcorder recording is not possible.	● The camcorder has not been properly	Confirm that the camcorder is properly
		connected.	connected.
		● The input mode is not correct.	Set the input mode to “L-1”, “L-2”, “F-1”
			or “S-1”.

TIMER RECORDING
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1.	Timer recording won’t work.	● The clock and/or the timer have been set	Re-perform the clock and/or timer
		incorrectly.	settings.
		● The timer is not engaged.	Press # and confirm that “#” is
			displayed on the front display panel.

2.	Timer programming is not possible.	● Timer recording is in progress.	Timer programming can’t be performed
			while a timer recording is in progress.
			Wait until it finishes.

3.	“#” and “[” on the front display	● The timer is engaged but there’s no	Load a cassette with the record safety tab
	panel won’t stop blinking.	cassette loaded.	intact, or cover the hole using adhesive
			tape.

4.	The power shuts off and “#” and	● The loaded cassette has had its record	Remove the cassette and cover the hole
	“[” on the front display panel won’t	safety tab removed.	with adhesive tape, or insert a cassette
	stop blinking.		with the record safety tab intact.
		● The end of the tape was reached during	The programme may not have been
		timer recording.	recorded in its entirety. Next time make
			sure you have enough time on the tape to
			record the entire programme.

5.	“#” blinks for 10 seconds and the	● # has been pressed when there are no	Check the programmed data and
	Timer mode is disengaged.	programs in memory, or the timer	re-program as necessary, then press #
		record information has been	again.
		programmed incorrectly.

6.	The SHOWVIEW system does not	● The recorder’s channel positions have	Refer to “Guide Program Number Set”
	timer-record properly.	been set incorrectly.	( pg. 79) and re-perform the procedure.

Image 83

JVC LPT0328 specifications Recording

Contents

Video Cassette Recorder Safety Precautions Moisture Condensation Front View Inside View of Front Panel Rear View ON-SCREEN Display Remote Control Remote Control LCD How To Use Connect the recorder to TV Check the contents10 EN Situate the recorder Video Connection 8To connect to a TV with S-VIDEO/AUDIO in connectorsPlug the end of the mains power cord into a mains outlet Select your country Auto Set Up12 EN Turn on the recorder Press rt to select Auto and press OK or e Perform Auto Set UpSelect the language Press rt to select your language code Press rt to select CH - and press OK or e Perform Preset Download14 EN Set the video channel Just Clock Language for the on-screen display 16 EN Access the Main Menu screenAccess the Country Set screen Language Make connections Installing Satellite ControllerSituate the Satellite Controller Attach the Satellite Controller 18 EN Setting satellite receivers brand and channel VCR Auto Standby Direct Rec TV Auto Power OnNexTView Link 20 EN Basic Playback Pause during playback Variable Speed SearchSlow Motion High-Speed Turbo Search Manual Index Mark/Erase 22 ENSkip Search Index Search Manual Tracking Next Function MemoryDigital TBC/NR Repeat Playback Activate Variable Speed Search Audio signal during TimeScanTimeScan 24 EN TimeScan 26 EN Tape Remaining Time Instant Timer Recording ITR Locate the start point Engage the Record-Pause mode28 EN Retake Audio Recording Level Control Engage the S-VHS ET modeAdjust the audio recording level Super VHS ET S-VHS ET Received Receiving Stereo and Bilingual ProgrammesOn-screen Display Recording Playback 32 EN Access the Showview displayAccess the Showview screen Access the Showview Program screen Guide Program Number Set Set the VPS/PDC modeEngage the recorder’s timer mode Satellite Receiver Users 34 EN Express Timer Programming Press PR+ To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Enter the channel position 36 EN Overlapping programmes blink on the TV screen Cancel or change programme settingConfirm the overlapping programmes Select the programme to modify 38 EN Select the L-2 Select modeRecording mode Programme Recording Re-supply the power Remote A/B Code SwitchingRemove the power supply Set the remote control code Operate the TV TV Multi-Brand Remote Control40 EN Set the TV brand code Operate the satellite receiver Satellite Receiver Multi-Brand Remote ControlSet the satellite receiver brand code Check Memory Navigation42 EN Navigation Playback Turn off Navigation Turn Off NavigationVideo Navigation Title Screen Check the memory Find Blank Space Access the Find Blank Space screenEdit Title 44 EN Select the tape title Access the Edit Title screenEdit Tape Title Entering Character Enter the programme title 46 ENChoice of Category Select the programme Delete the programme data Delete Tape DataDelete Programme Data Delete the tape data Sort By Tape Number Access the Find Title screenFind Title 48 EN Select the programme Access the Tape No. screenAccess the Date screen Sort By Date Category you want to watch Access the Category screen50 EN Sort By Category Start the camcorder Set the recorder’s input modeSet the edit mode Edit From a Camcorder Output/Input Set Decoder connector Select and L-2 Input Setting 54 EN Another Video Recorder Recorder Player CD player, etc Audio Dubbing56 EN Pre-recorded tape Audio-dubbed tape Press AUX number key 0 and/or PR to select F-1 or S-1 Engage the Audio Dubbing modeStart dubbing End Audio Dubbing After Insert Editing Insert Editing58 EN Source tape Before Insert Editing Recording tape Start Editing Engage the Insert Editing modeAV Insert Editing Locate the end point Start playback of the source cassette Access the R.A.Edit screen60 EN Load the source cassette End Random Assemble Editing Memory CapacityPrepare the recording deck Start Random Assemble Editing Press Synchro 7/79 62 ENStart Synchro Editing Pause Synchro Editing Examples Access the Jlip ID No. Set screenSet the Jlip ID number Jlip ID Number Simple Connections Connecting To a Satellite Receiver Satellite receiver Decoder Back of recorder Perfect Connections Set the tuner Select the input mode66 EN Connect the decoder Make connections Connecting/Using a Stereo System Select the mode setting Mode SetAccess the Mode Set screen Select the mode Off, and automatically disengaged when the recorder is You can set the B.E.S.T. Biconditional Equalised SignalThis feature helps you to adjust the playback picture When this function is set to ON, the timer is For Example 70 EN About Ntsc Playback Auto Channel Set Access the Auto Channel Set screenTuner Set 72 EN Press OK twice Perform Auto Channel SetView the Confirmation screen Manual Channel Set 74 EN Delete a Channel When Receiving a Scrambled Broadcast Set Stations B 76 ENSet Stations a Station Name TV Station And ID List 78 EN Access the Video Channel Set modeExit the Video Channel Set mode Video Channel Set Enter the Guide Program number Showview System SetupGuide Program Number Set Guide Program Number 80 EN Access the Clock Set screenClock Set Start the clock operation Set the date and timeSet Just Clock Set the source channel position for clock data 82 EN Troubleshooting Recording 84 EN Other Problems Playback 86 EN Clock Set Preset DownloadTimer Warning Display TimeScan Tuner Set AV Insert Editing S.T. Picture System Country code International telephone Language code